Ryobi RLT30SESF Bedienungsanleitung Seite 16

GB
F D E I
Carefully pour fuel mixture into the tank. Avoid spillage.
■
Immediately replace fuel cap and hand tighten.
■
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
Note: It is normal for smoke to be emitted from a new
engine during and after first use.
WARNING
Always shut off engine before fueling. Never add
fuel to a machine with a running or hot engine.
Move at least 9 m from refueling site before
starting engine. Do not smoke!
1 Litre + 20 ml
2 Litres + 40 ml
3 Litres + 60 ml
4 Litres + 80 ml
5 Litres + 100 ml =
STARTING AND STOPPING (Fig. 4)
WARNING
Never start or run the engine inside a closed or
poorly ventilated area; breathing exhaust fumes
can kill.
NOTE: Be sure to return the stop switch to the "I" (RUN)
position before trying to start unit.
Ensure the on / off switch is in the "on" position.
■
Press the primer bulb 7 times.
■
With a firm grip of the handle, pull the starter cord
■
until the engine starts.
Squeeze the trigger to run.
■
If the engine does not start after six pulls, squeeze
■
the trigger to full throttle and hold while pulling
the starter grip.
When you have completed your task, turn the on / off
■
switch to the "off" position.
OPERATING THE TRIMMER (Fig. 5)
Hold the trimmer with the right hand on the rear handle
and the left hand on the front handle. Keep a firm grip
with both hands while in operation. Trimmer should be
held at a comfortable position with the rear handle about
hip height.
Always operate trimmer at full throttle. Cut tall grass
from the top down. This will prevent grass from wrapping
around the shaft housing and bump head which may
cause damage from overheating. If grass becomes
P NL S DK N FIN GR HU
=
=
= 50:1 (2%)
=
CZ RU RO PL SLO HR TR EST LT
English
wrapped around the bump head, stop the engine,
disconnect the spark plug wire, and remove the grass.
CUTTING TIPS (Fig. 6)
ADVANCING THE LINE (Fig. 7)
TM
For Reel Easy
MAINTENANCE
WARNING
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to
do so can cause possible injury, poor perfor-
mance and may void your warranty.
You may make adjustments and repairs described
■
here. For other repairs, have the trimmer serviced by
an authorized service agent.
Consequences of improper maintenance may
■
include excess carbon deposits resulting in loss
of performance and discharge of black lubricanty
residue dripping from the muffler.
Make sure all guards, straps, deflectors and handles
■
are properly and securely attached to avoid the risk of
personal injury.
For RLT30CESF only: the cutting attachment must not
■
work in idle mode. If this requirement is not satisfied,
the clutch has to be adjusted or the machine needs an
urgent maintenance by a qualified technician.
LINE REPLACEMENT (Fig. 8)
TM
For Reel Easy
CLEANING THE EXHAUST PORT AND MUFFLER
Depending on the type of fuel used, the type and amount
of lubricant used, and/or your operating conditions, the
exhaust port and muffler may become blocked with
carbon deposits. If you notice a power loss with your
petrol powered tool, a qualified service technician will
need to remove these deposits to restore performance.
SPARK ARRESTOR
The spark arrestor must be cleaned or replaced every
25 hours or yearly to ensure proper performance of
your product. Spark arrestors may be in different locations
depending on the model purchased. Please contact
your nearest service dealer for the location of the spark
arrestor for your model.
CLEANING THE AIR FILTER SCREEN (Fig. 9)
Remove the air filter cover by pushing down on the
■
latch with your thumb while gently pulling on the cover.
Brush the air filter screen lightly to clean.
■
Replace the air filter cover by inserting the tabs on the
■
bottom of the cover into the slots on the air filter base;
push the cover up until it latches securely in place.
13 13
LV
Only
Only
SK BG