Simons Voss Technologies Digital SmartHandle AX Kurzanleitung Seite 28

10. Removing the fitting
9. Press down the spring plate bracket.
28
The inner handle is now ready.
9
29
10. For 7 mm spindle: insert the adapter sleeve onto the side of the spindle
with the pin.
30
11. For 8.5 mm and 10 mm spindle: slide the adapter sleeve into the centre
of the spindle. Use a punch and hammer to make an indent in the ad-
apter sleeve to prevent it from slipping.
31
32
12. Insert the spindle with the pin side into the fitting.
9 Pin will snap into position in the mount.
33
13. Insert the fitting with the spindle into the door from the outside.
34
14. Fasten the escutcheon base firmly with the L1 screws (PH2, torque 1.1
Nm).
35
36
15. For non-MO: fasten the inner handle with the L2 screws (PH2, torque 1.1
Nm).
37
16. For non-MO: position the escutcheon cover on the escutcheon base.
38
17. Fasten the set screw on the inner handle firmly (TX15, torque 5.0 Nm).
39
18. Fit the outside handle into position on the fitting.
40
19. Firmly fasten the grub screw on the outside handle (TX15; torque: 5.0
Nm).
41
Fitting is now installed.
9
10. Removing the fitting
ü 1.5 mm hexagonal wrench available.
1. Remove the fitting in the reverse order to installation.
2. Insert a 1.5 mm hex key into the hole in the spindle mount in the fitting.
42
3. Bend the hex key to the side where the hole is located while pulling on
the outside handle.
43
9 Fitting is now removed.
11. Replacing the batteries
NOTE
Malfunctions due to poor contact or different discharge
Contact surfaces that are too small/contaminated or different discharged
batteries can lead to malfunctions.
1. Only use batteries that are approved by SimonsVoss.
2. Do not touch the contacts of the new batteries with your hands.
3. Use clean and grease-free gloves.
4. Always replace all batteries at the same time.
28 / 52
Digital SmartHandle AX Scandinavian Oval
ü Special tool at hand.
Gloves at hand.
ü
1. Insert the special tool into the fitting's cover inlay.
44
2. Remove the cover with the tool.
45
46
3. Carefully bend the battery clip inwards to detach it.
47
48
4. Open the battery holder.
49
5. Remove the battery holder.
50
6. Remove the old batteries.
51
7. Insert the new batteries with the positive terminals next to each other
(type CR2450).
52
8. Put the battery holder back into place.
53
9. Reattach the battery clip.
54
10. Replace the cover on the fitting.
55
11. Snap the cover back into place.
56
9 Batteries are now replaced.
12. Technical data
Operating temperature range
Battery type
Battery manufacturer
IP protection rating
Radio emissions
15.24 kHz - 72.03 kHz
Only for item numbers: SV-S2.*A*,
SV-S2.*AM*, SV-S2.*LN*
13.560006 MHz - 13.560780 MHz
868.000 MHz - 868.600 MHz /
869.700 MHz - 870.000 MHz
Only for item numbers: SV-S2.*LN*,
SI-S2.*M.WO*
2402 MHz - 2480 MHz
13. Declaration of conformity
The company SimonsVoss Technologies GmbH hereby declares that the
articles (SV-S2.*A*, SV-S2.*AM*, SV-S2.*LN*, SI-S2.*M.WO*, SI-
S2.*M.VCN*) comply with the following guidelines:
 2014/53/EU -RED-
or for the UK: UK statutory 2017 No. 1206 -Radio equipment-
2011/65/EU -RoHS-

or for the UK: UK statutory 2012 No. 3032 -RoHS-
-25 °C to +50 °C
4x CR2450 (3V)
Murata

Varta

Panasonic

IP40
10 dBµA/m (3 m distance)
1.04 dBµA/m (3 m distance)
<25 mW ERP
2.5 mW
EN