Simons Voss Technologies Digital SmartHandle AX Kurzanleitung Seite 27

Digital SmartHandle AX Scandinavian Oval
NOTE
Effect on the mortise lock
The SmartHandle AX acts exclusively on the latch of the mortise lock.
Locking and insurances
Insurance companies place increased demands on a closure.
1. If you want to lock the door under insurance law, use a self-locking
panic lock or a locking cylinder in addition to the SmartHandle AX.
2. Pay attention to the approvals according to EN 179.
SmartHandle AX with self-locking panic lock
The SmartHandle AX only offers full functionality with a self-locking panic
lock.
1. Combine the SmartHandle AX with a self-locking panic lock.
2. Pay attention to the declarations of conformity of the lock manufactur-
ers according to EN 179.
Conditions for authorisation security
Operation with Mifare Classic and/or PinCode keypad excludes authorisation
security class D according to DIN EN 16867:2020.
Sealing escutcheon holes
Any escutcheon holes that exist may be used to manipulate the lock.
1. Seal any escutcheon holes with a blind cylinder, for example.
2. In the case of FH versions, you must be install a brass dummy cylinder or
locking cylinder.
4. Scope of delivery
SmartHandle AX (Scandinavian Oval)

Special tool

Quick guide

Depending on version:
Adapter set, 7 mm spindle

 Adapter sleeve, 8.5 mm spindle
 Adapter sleeve, 10 mm spindle
Blank cylinder

5. Design
1
2
6. For door thickness X: prepare threaded
rods and spindle
ü Saw at hand.
ü Vernier calliper at hand.
ü PH2 screwdriver at hand.
1. For X: measure the door thickness.
3
2. For X: fasten the screws, threaded sleeves and threaded rods together.
4
3. For X: mark the sawing points on the threaded rods and spindle.
5
6
7
4. For X: use a suitable saw to cut the threaded rods and spindle.
8
EN
7. For inner door handle, clockwise: pre-
pare stud bolts
TX3 screwdriver at hand.
ü
1. Check whether you need to turn the inner handle clockwise.
9
9 If yes, refit the SmartHandle AX's stud nuts as described.
2. Unscrew the SmartHandle AX rear (TX8).
10
3. Unscrew the stud nuts.
11
4. Re-fasten the stud nuts firmly in the new positions.
12
5. Screw the SmartHandle AX rear firmly into place again (TX8, torque 1.1
Nm).
13
Stud nuts are fastened through the SmartHandle AX rear again.
9
8. Programming the fitting
Programme the fitting before installation. You can use different
programming devices, depending on the product family.
14
15
16
9. Installing the fitting
ü Door pre-drilled.
ü PH2 screwdriver at hand.
ü TX15 screwdriver at hand.
Vernier calliper at hand.
ü
Pincers at hand.
ü
1. For S, M and L: measure the door thickness.
17
2. For S, M and L: determine the separation points on the cut-to-length
screws L1 and L2.
18
19
3. For S, M and L: trim the cut-to-length screws L1 and L2.
20
4. For 7 mm spindle: place the adapter sleeve in the inner handle in such a
way that the recess faces the grub screw.
21
5. Determine your inner handle's direction rotation as viewed from the in-
side: clockwise (clockwise = CW) or anti-clockwise (counter-clockwise
= CCW).
22
23
6. Insert the interchangeable plate into the inner handle as required.
24
25
7. Press the spring plate on one side against the interchangeable plate so
that the spring is compressed.
26
8. At the same time, hook the spring plate tabs into the slot in the inner
handle.
27
4. Scope of delivery
27 / 52