AL-KO SnowLine 760.4 TE LED Betriebsanleitung Seite 41

Operation
7 OPERATION
7.1 Starting clearing (40 - 42)
WARNING! Danger from rotating appli-
ance parts! Reaching into rotating appliance
parts will result in serious injuries!
■
Never reach into the rotating transport auger!
WARNING! Objects being discharged!
Risk of injury and risk of material damage due to
objects being discharged!
■
Never turn the discharge channel in the di-
rection of persons, animals, windows, cars or
doors.
1. Start clearing.
2. Check the position of the snow discharge
spout and adjust the discharge direction us-
ing the hand crank (40/1).
3. Adjust the discharge height (40/2).
4. Start the engine (see chapter 6.7 "Starting
the engine (32 - 37)", page 40).
5. Engage the gear for the travel drive (41/3):
■
1 to 6 are forward gears, with 1 the low-
est and 6 the highest gear.
■
R1 and R2 are reverse gears, with R1
the lower and R2 the higher gear.
6. Push clutch lever (41/4) for the auger drive
(41/a).
7. Push clutch lever (42/5) for the travel drive
(42/a).
7.2 Stopping clearing (43)
1. Release the clutch lever (43/1) to disengage
the auger drive and travel drive (43/a).
To prevent freezing, allow transport auger and
discharge wheel to continue to run until they are
more or less free of snow. A frozen transport au-
ger would damage the V-belts.
The snow blower comes to a standstill, transport
auger and discharge wheel stop.
7.3 Changing gear for the travel drive (42 -
44)
IMPORTANT! Risk of damage to the appli-
ance. The transmission is damaged if the clutch
is not disengaged before the gear change.
■
First disengage the clutch, then change
gears.
1. Release clutch lever for the travel drive
(43/1), i.e. disengage (43/a).
Note: The transport auger blocks when it is
474911_e
stopped in wet and heavy snow and then re-
started. Do not release the clutch lever for
the auger drive!
2. Change gear with gear lever (44/1).
3. Push clutch lever (42/5) for the travel drive
(42/a).
7.4 Selecting the operating mode on 760.4
TE LED
The operating mode lever (02/23) can be used to
adjust the height of the transport auger, clearing
plate and plough by displacing the weight of the
snow blower.
■
"Transport": The weight lies on the rear area
of the snow blower, so that the transport au-
ger and plough are away from the ground
and the snow blower can be easily pushed.
■
"Normal": Horizontal position of the snow
blower for normal operation.
■
"Packed Snow": With dense snow, the weight
can be moved to the front area of the snow
thrower with this setting.
7.5 Steering the 760.4 TE LED snow blower
(45)
1. Steering the snow blower to the left: Tighten
the left tilt lever (45/1) (45/a).
2. Steering the snow blower to the right: Tighten
the right tilt lever (45/2) (45/b).
7.6 Clearing clogging in the snow discharge
spout (43, 46)
NOTE Allow the transport auger to run at all
times, if possible, in order to avoid clogging in
heavy and wet snow.
If the snow is no longer discharged correctly,
snow and ice deposits on the transport augers
and in the discharge channel may be the cause.
1. Release the clutch lever (43/1) to disengage
the auger drive and travel drive (43/a).
2. Switch off the engine (see chapter 6.8 "Stop-
ping the engine (38, 39)", page 40).
3. Carefully clear the snow from the discharge
channel and transport auger using the clean-
ing tool (46/1).
If the snow discharge is still unsatisfactory, take
the appliance to a specialist workshop.
41