R&G CP0426BL Montageanleitung Seite 23

STURZPADS ZUM VORDERTEIL DES MOTORRADS GERICHTET. Noch etwas
drehen, bis Sie merken, dass der Druck sich leicht erhöht, dann noch eine Vierteldrehung
anwenden. Nicht überdrehen – dies kann zu einer Beschädigung des Motorrades führen. 40
Nm Anzugsmoment nicht überschreiten!

Überprüfen Sie, dass das Sturzpad ordnungsgemäß montiert ist und die Verkleidung nicht
berührt, bevor Sie die sechs Schrauben, die die linke Seitenverkleidung in Position fixieren
und wieder befestigen.

Montieren Sie die Plastikabdeckung unter dem Verkleidungsoberteil wieder mit den sechs
Plastikschrauben.

Wenn noch nicht bereits montiert, montieren Sie die Bubble-Aufkleber in den Vertiefung der
Sturzpad-Schutzkappen

Die Sturzpad-Schutzkappen an beiden Sturzpads abringen – siehe Abbildung 29.

Stellen Sie sicher, dass die Verkleidungen wieder ordnungsgemäß montiert sind, und dass die
Sturzpads sicher befestigt sind, bevor Sie mit dem Motorrad fahren.
Eine digitale Version dieser Montageanleitung kann auf folgender Seite heruntergeladen werden:
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their
performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has
been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable
quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free
of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the
Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from
accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer
must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a
25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
AUSGABE 1 25/08/2017 (AR)
AUSGABE 2 07/09/2017 (AR)
www.rg-racing.com
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
CP0426
Email: info@rg-racing.com