Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Once correctly positioned, tighten this bolt to the manufacturers recommended torque settings.
With the right side fairing off the bike, remove the two Phillips headed fasteners that secure
the black plastic infill panel in place from behind, before unclipping from the top edge and
removing from the fairing. Remove one of the rubber pieces from one of the plastic mounts.
Peel the backing off the adhesive foam that has been applied to the reverse of the right side
R&G plastic panel (item 13 – PP0007), before re-sticking the small rubber piece that was
removed from the OEM panel.
Fit the R&G plastic panel to the fairing in the same way that the OEM panel was removed, by
clipping in the top edge before re-fitting the OEM plastic fasteners, as shown in picture 25.
With the metal block fitted to the bike, apply the remaining length of the self-adhesive foam
(item 17) to the metal block, as shown in picture 26.
Re-fit the fairing to the bike and the new plastic panel should fit neatly around the metal
block, as shown in picture 27.
Take the right side cover plate (item 16 – SMW0090) and locate over the plastic panel and
metal block, whilst fitting the M5 x 6mm long button head bolt (item 9) through the mounting
hole on the rear and into the threaded hole on the metal block, as shown in picture 28. We
advise to use a bull nose allen key to tighten this bolt as access is restricted. The large hole on
the front of the cover plate should now align and sit over the stepped boss on the threaded
mounting hole of the metal block.
Slide the remaining smaller washer (item 3 – S0018 – 3.25mm long) onto the remaining M10
x 1.25 x 60mm long hex head bolt (item 2) so the spacer sits against head of bolt. Slide one
serrated locking washer (item 4) over the bolt so it sits against the spacer just fitted.
Next slide the bolt with spacer & washer through a crash protector (item 5) so the head of the
bolt and washers go into the counter-bore of the bobbin.
Locate the remaining longer spacer (item 6 – S0250 – 7.50mm long) over the exposed end of
the bolt and tighten into the threaded boss on the metal block, as shown in pictures 29.
Tighten the crash protector bolt until you feel some compression from inside the protector
using a 17mm socket and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST
BE POSITIONED AS IN PICTURE 'C' WITH BIGGER END TOWARD FRONT OF
BIKE. Turn a little more so that you feel the compression increase slightly. Then apply a
quarter turn. Do not over tighten as damage can occur to the bike. Do not exceed 40N/m of
torque.
Ensure the crash protector is correctly fitted and clears the fairing, before re-fitting the six
bolts that secure the left side fairing panel in place.
Re-fit the plastic panel that fits under the nose of the bike along with the six plastic fasteners.
If not already fitted fit bubble stickers into recess of both crash protector caps.
Fit crash protector caps into both crash protectors, as shown in picture 29.
Ensure the fairings are correctly fitted and that the crash protectors are securely tightened
before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1 25/08/2017 (AR)
ISSUE 2 07/09/2017 (AR)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
CP0426
www.rg-racing.com
Email:
info@rg-racing.com
Werbung
