Stiga AM 98 Li 48 V1 Betriebsanleitung Seite 267

NOTE
The battery can be recharged at any time, even
partially, with no risk of damaging it.
SAFETY INSTRUCTIONS
Do not perform any maintenance or cleaning
while recharging the batteries.
To recharge the battery:
• Bring the machine close to an earthed power
outlet (so as to avoid the use of extensions)
and remove the key;
• Open the rear flap (fig. 16.A, fig. 8.G);
• Connect the battery charger (fig. 16.D)
provided to the charge socket (fig. 16.B) using
the proper bayonet connector (fig. 16.C);
• Connect the battery charger to the mains
socket, by inserting the respective plug (fig. 17).
In certain commercial areas only:
To charge the battery, a socket with a safety
circuit breaker (fig. 18.A) is supplied, if
required, to which the charging cable must be
connected (fig. 16.D).
The socket with a safety circuit breaker must
be connected to the mains socket and a
performance test must be carried out:
1. Press the "RESET" push-button (fig. 18.B)
to activate functioning. The warning light
must be "ON" (fig. 18.C).
2. Press the "TEST" push-button (fig. 18.D) to
perform the performance test. The warning
light must be "OFF" (fig. 18.C).
DANGER
If the performance test ends with a negative
result, the safety circuit breaker socket is
not required and should not be used. If the
performance test is successful, it can be used
and it is possible to proceed with the charging
phase.
Full charging takes about 2-8.5 hours (depending
on the battery, the charger size and ambient
temperature), during which the warning LEDs
(fig. 9.B) flash progressively. When every single
charge threshold is reached, the respective
LED remains on permanently, while the others
continue to flash.
The battery can be kept under charge indefinitely.
Charge status
(SOC)
SOC > 80%
60% ≤ SOC < 80%
40% ≤ SOC < 60%
20% ≤ SOC < 40%
10% ≤ SOC < 20%
It is possible to stop charging the battery when
the charge level is between LEDs 1 and 4.
WARNING
Do not interrupt the charging phase when LED 5
flashes but wait for it to be lit continuously. When
all LEDs are lit continuously the battery is fully
charged.
NOTICE
The battery charging time could increase if
the machine has been used in heavy working
conditions, with a consequent indication of
battery overheating (chap.15).
NOTICE
If the battery is completely discharged, the
indicator LEDs remain off until the minimum
charge threshold is reached.
When charging is complete, the charging system
reduces the flow of current sufficient to maintain
and restore the charge of the battery to its ideal
levels
NOTICE
If the battery charger is connected to the machine
and the 5 LEDs fig 9.B flash at the same time, it
means that charging is not in progress. Check the
connection battery charger/electric mains.
NOTE
The energy consumption to maintain the battery
charged is very low and inexpensive.
EN - 21
LED Led
switching on lighting
(type "III")
1 2 3 4 5 1
1 2 3 4 5
1 2 3 4 5
2
1 2 3 4 5
1 2 3 4 5
1
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5 2
1 2 3 4 5
1 2 3 4 5
1
1 2 3 4 5
2
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1
1 2 3 4 5
2
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1
2
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
5
4
3
5
4
3
5
4
3
5
4
3
5
4
3