Emerson Micro Motion 2700 Konfigurations- Und Bedienungsanleitung Seite 168

Modell 2700 PROFIBUS Blockparameter
Tabelle F-5 Parameter Transducer Block 1 (Fortsetzung)
Index Parameter Mnemonik
139 PA_StatusWords1 (DD Name:
Alarm Eins Status)
140 PA_StatusWords2 (DD Name:
Alarm Zwei Status)
141 PA_StatusWords3
(DD Name: Alarm Drei Status)
142 PA_StatusWords4
(DD Name: Alarm Vier Status)
143 PA_StatusWords5
(DD Name: Alarm Fünf Status)
160
Definition
Status Wort 1
Status Wort 2
Status Wort 3
Status Wort 4
Status Wort 5
Nachrichten Datentyp/ Grösse Speicher/
Typ Struktur Rate (HZ)
ENUM BIT_ 2 D/20
ENUMERAT
ED
ENUM BIT_ 2 D/20
ENUMERAT
ED
ENUM BIT_ 2 D/20
ENUMERAT
ED
ENUM BIT_ 2 D/20
ENUMERAT
ED
ENUM BIT_ 2 D/20
ENUMERAT
ED
Auswerteelektronik Modell 2700 mit PROFIBUS-PA
Voreinge- Zugriff Aufzählende Liste
stellte Wert der Werte/Bereiche
– R 0x0001 = Core EEPROM
Checksum Error
0x0002 = Core RAM
Test Error
0x0004 = Not Used
0x0008 = Sensor Failure
0x0010 = Temp OOR
0x0020 = Cal Failed
0x0040 = Other Failure
0x0080 = Xmitter Init
0x0100 = Not Used
0x0200 = Not Used
0x0400 = Simulation
Mode Active (A132)
0x0800 = Not Used
0x1000 = Watchdog
Error
0x2000 = Not Used
0x4000 = Not Used
0x8000 = Fault
– R 0x0001 = Not Used
0x0002 = Not Used
0x0004 = Not Used
0x0008 = Not Used
0x0010 = Density OOR
0x0020 = Drive OOR
0x0040 = Not used
0x0080 = Not Used
0x0100 = NV err (CP)
0x0200 = RAM err (CP)
0x0400 = Sensor Failure
0x0800 = Temp OOR
0x1000 = Input OOR
0x2000 = Not Used
0x4000 = Xmitter not
Char
0x8000 = Not Used
– R 0x0001 = Not Used
0x0002 = Power Reset
0x0004 = Xmitter Init
0x0008 = Not Used
0x0010 = Not Used
0x0020 = Not Used
0x0040 = Not Used
0x0080 = Not Used
0x0100 = Cal Failed
0x0200 = Cal Fail: Low
0x0400 = Cal Fail: High
0x0800 = Cal Fail: Noisy
0x1000 = Xmtr Failed
0x2000 = Data Loss
0x4000 = Cal in Progress
0x8000 = Slug Flow
– R 0x0001 = API: Temp
OOR
0x0002 = API: Dens OOR
0x0004 = Line RTD OOR
0x0008 = Meter RTD
OOR
0x0010= Reverse Flow
0x0020 = Factory Config.
Data Invalid
0x0040 = ED: bad curve
0x0080 = LMV Override
Active
0x0100 = ED: Extrap
error
0x0200 = Need cal factor
0x0400 = Not Used
0x0800 = Not Used
0x1000= Xmitter not Char
0x2000 = NV err (CP)
0x4000 = NV err (CP)
0x8000 = NV err (CP)
– R 0x0001 = Boot sector
(CP)
0x0002 = Not Used
0x0004 = Not Used
0x0008 = Not Used
0x0010 = Not Used
0x0020 = Not Used
0x0040 = D3 in progress
0x0080 = D4 in progress
0x0100 = Not Used
0x0200 = Not Used
0x0400 = Temp slope in
progress
0x0800 = Temp offset in
progress
0x1000 = FD in progress
0x2000 = D2 in progress
0x4000 = D1 in progress
0x8000 = Zero in
progress
Modbus
Register/
Speicher
R-419
R-420
R-421
R-422
R-423