Electrical Safety; Assembling; Before The First Start-Up - ATIKA BWS 700 N-2 Originalbetriebsanleitung

 removal of faults (this also includes the removal of jammed
splinters)

checks of connecting lines, whether these are knotted or
damaged
 transporting the saw
 changing the saw blade

leaving the saw (also for short-term interruption)
 Maintain your saw with care:
 Keep your tools sharp and clean in order to be able to work better
and safer.
 Follow the maintenance instructions and the instructions for tool
exchange.

Keep handles dry and free of oil and grease.
 Check the machine for possible damage:
 Before further use of the machine the protection devices or
slightly damaged parts must be checked carefully for their proper
and intended function.

Check whether the movable parts function perfectly and do not
stick or whether the parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation of the saw.
 Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar as
nothing else is stated in the instructions for use.
 Damaged or illegible safety labels should be replaced
immediately.
Do not allow any tool key to be plugged in!

Before switching on, check always that wrenches and adjusting tools
are removed.
Store unused equipment in a dry, locked place out of the reach of

children.
Adopt safe procedures for cleaning, maintenance and regular

removal of chips and dust to prevent the risk of fire.
Make sure during its entire foreseeable life cycle that the machine

including its parts cannot tip over or move in an uncontrolled manner
when transporting, assembling, putting out of service and scrapping

Electrical safety

 Design of the connection cable according to IEC 60 245 (H 07 RN-F)
with a core cross-section of at least
 1.5 mm² for cable lengths up to 25 m
 2.5 mm² for cable lengths over 25m
 Long and thin connection lines result in a potential drop. The motor
does not reach any longer its maximal power; the function of the
device is reduced.
 Plugs and coupler outlets on connection cables must be made of
rubber, plasticised PVC or other thermoplastic material of same
mechanical stability or be covered with this material.
 Protect yourself against an electric shock. Avoid touching earthed
parts with your body.
 The connector of the connection cable must be splash-proof.
 Wind off completely the cable when using a cable drum.
 Do not use the cable for purposes for which it is not meant. Protect
the cable against heat, oil and sharp edges. Do not use the cable to
pull the plug from the socket.
 Regularly check the saw cable and if damaged, have it renewed by a
recognised skilled electrician.
 When running the connection line observe that it does not interfere, is
not squeezed, bended and the plug connection does not get wet.
 Regularly check the extension cables and replace them if they are
damaged.
 Do not use any defective connection cables.
 When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
 Do not set up any provisional electrical connections.
 Never bypass protective devices or deactivate them.
14
 Only hook up the machine by means of a fault-current circuit breaker
(30 mA).
The electrical connection or repairs to electrical parts of the machine
must be carried out by a certified electrician or one of our customer
service points. Local regulations – especially regarding protective
measures – must be observed.
Repairs to other parts of the machine must be carried out by the
manufacturer or one of his customer service points.
Use only original spare parts. Accidents can arise for the user
through the use of other spare parts. The manufacturer is not liable
for any damage or injury resulting from such action.

Assembling

Assembling the wheels
Slide each one spacer sleeve (1A) and one wheel
(1) on both axle ends of the preassembled unit.
Secure them each with a washer and a screw. [2x screw M8x20, 2x
washer A10.5]
Assembling the connecting bar
Mount the connecting bar (23) to the device unit.
[4x screw M8x20, 8x washer A8.4, 4x nut M8 self-locking].
Assembling the switch / cable holder
Bolt the switch base (a) to the frame.
[2x screw M8x20, 4x washer A8.4, 2x nut M8 self-locking].
Assembling the cable holder (b) [1x screw M4x15, 1x cable holder,
2x washer A4, 1x nut M4, self-locking].

Before the first start-up

 To achieve flawless functioning of the machine, please follow the
instructions listed:
 Place the saw at a location which meets following conditions:
 outdoor
 secured against slipping
 free of vibrations
 even
 free of tripping hazards
 adequate light
 To ensure a safer foothold when working with the saw secure the saw
against rolling away.
 Before each use, check
 connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
 that the plastics inserts is in a proper condition
 the saw blade for flawless condition
 the functioning of the jigging device
 Do not use any cracked saw blades or such that have changed their
shape.
 Do not use any saw blades made of HSS steel.
 Immediately replace a worn or damaged plastics inserts.
 Assume the correct work posture. Stand in front of the operating side
frontally to the saw blade line.