Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Use a tamper or hook to remove jammed objects from the
hopper or ejection slot.
Always wait until the shredder has come to a complete
standstill before restarting it.
Electrical mains supply impedance
When conditions in the electrical mains supply are un-
favourable, voltage reductions for short periods can occur dur-
ing the process of turning on the equipment, which can adverse-
ly affect other equipment (e.g., the flickering of a lamp).
No breakdowns are to be expected if the maximum, electrical
mains supply impedances given in the table are met.
Power consumption P1 (W)
2800
W
o
r
k
i
n
g
w
i
t
h
W
o
r
k
i
n
g
w
i
t
h
Choose a working position alongside the equipment or
behind it. Never stand near the ejection opening.
Longer material that is protruding from the device could
spring back when it is drawn in by the blades! Observe
safety distance!
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Never place hands, other parts of the body or clothing into
the filler funnel, ejection channel or in the vicinity of other
moving parts.
Check that no chopped residues are in the filling hopper
before switching on the equipment.
Do not tip or tilt the machine when the motor is running.
When filling, be careful that no pieces of metal, stones,
bottles or other objects unintended for processing, enter the
filling hopper.
Immediately switch off the equipment and allow it to come to
a stop, if foreign objects enter the filling hopper or if the
equipment starts to make unusual noises or vibrates. Re-
move the mains plug and carry out the following checks:
inspect for damage,
−
replace or repair damaged parts,
−
− check the equipment and tighten loose parts.
You must not repair the equipment yourself if you are
unauthorized to do so.
What can I shred?
Yes:
•
all types of branches up to a max. diameter, depending on
wood species and freshness.
• withered garden refuse which has lain a number of days.
Only shred in alternation with branches.
No:
•
glass, metal, plastic, plastic bags, stones, cloth, roots with
soil
•
refuse which does not have a solid consistency, e. g. kitchen
waste
14
Electrical mains supply
impedance Zmax (W)
0,19
t
h
e
g
a
r
d
e
n
s
h
r
e
d
d
e
r
t
h
e
g
a
r
d
e
n
s
h
r
e
d
d
e
r
Special tips on shredding:
Always fill the material to be shred-
ded into the filling hopper from the
right.
Branches, twigs and wood should
be broken down immediately after
they have been cut.
Material of this kinds gets very hard when it is dry, and
−
the maximum allowed branch diameter to be processed
has to be reduced.
Remove any side shoots from branches with a large num-
ber of twigs.
How to shred garden and kitchen waste with hight water
content and a tendency to clog
to prevent the machine from clogging, alternate waste
−
with wood containing material.
Do not allow the shredded material to pile up too high in the
area of the ejection opening. This can lead to shredded ma-
terial blocking the ejection channel, and backing up to the
filler opening.
Clean out the filler opening and ejection channel thoroughly
if the machine becomes blocked. Before doing this, switch
the motor off and disconnect the machine from the mains
power supply.
Please do not exceed the maximum branch diameter speci-
fied (cutting fresh wood) for your appliance (∅ see "Tech-
nical data"). Depending on the wood's nature and freshness
the maximum branch diameter the machine can process
may be smaller.
The cutter automatically draws the shredding material into
the machine through the slow rotation of the cutting rollers.
Automatic switch-over in the direction of rotation:
If the unit suddenly clogs, the blades may start to turn in the
opposite direction and push the shredded material back
out.
Switch off unit
−
Wait until the blades come to a standstill
−
Switch unit back on and use material which is easier to
−
process.
If the machine is overloaded, a protective motor switch en-
sures that the machine turns itself off automatically.
Turn the shredder on again after about 5 minutes.
−
If you cannot turn on the machine after this waiting time
−
refer to „Operational faults".
A
d
j
u
s
t
i
n
g
t
h
e
A
d
j
u
s
t
i
n
g
t
h
e
It is possible to adjust the counter blade
(B) at the cutting roller (A) free of
clearance. For an effective operation, an
as small as possible clearance should be
maintained.
Soft material or wet branches may tear instead of being cut. A
counter blade that is worn after repeated use may also lead to
this problem.
f
i
x
e
d
c
o
u
n
t
e
r
b
l
a
d
e
f
i
x
e
d
c
o
u
n
t
e
r
b
l
a
d
e
Werbung
Kapitel
Inhaltsverzeichnis
