Siemens SINUMERIK 840D sl Bedienhandbuch Seite 14
Vorschau ausblenden
Andere Handbücher für SINUMERIK 840D sl:
- Funktionshandbuch (2196 Seiten) ,
- Handbuch (1886 Seiten) ,
- Diagnose-handbuch (1476 Seiten)
Werbung
Inhaltsverzeichnis
10.3.9
Abspanen Rest (CYCLE952)...............................................................................................465
10.3.10
Stechen (CYCLE952)...........................................................................................................467
10.3.11
Stechen Rest (CYCLE952)..................................................................................................473
10.3.12
Stechdrehen (CYCLE952)...................................................................................................475
10.3.13
Stechdrehen Rest (CYCLE952)...........................................................................................481
10.4
Fräsen..................................................................................................................................484
10.4.1
Planfräsen (CYCLE61).........................................................................................................484
10.4.2
Rechtecktasche (POCKET3)...............................................................................................487
10.4.3
Kreistasche (POCKET4)......................................................................................................497
10.4.4
Rechteckzapfen (CYCLE76)................................................................................................507
10.4.5
Kreiszapfen (CYCLE77).......................................................................................................513
10.4.6
Mehrkant (CYCLE79)...........................................................................................................520
10.4.7
Längsnut (SLOT1)................................................................................................................525
10.4.8
Kreisnut (SLOT2).................................................................................................................534
10.4.9
Offene Nut (CYCLE899)......................................................................................................542
10.4.10
Langloch (LONGHOLE) - nur bei G-Code-Programm.........................................................552
10.4.11
Gewindefräsen (CYCLE70)..................................................................................................554
10.4.12
Gravur (CYCLE60)...............................................................................................................558
10.5
Konturfräsen.........................................................................................................................565
10.5.1
Allgemeines..........................................................................................................................565
10.5.2
Darstellung der Kontur.........................................................................................................565
10.5.3
Neue Kontur anlegen...........................................................................................................566
10.5.4
Konturelemente erstellen.....................................................................................................569
10.5.5
Kontur ändern......................................................................................................................574
10.5.6
Konturaufruf (CYCLE62) - nur bei G-Code-Programm........................................................575
10.5.7
Bahnfräsen (CYCLE72).......................................................................................................576
10.5.8
Konturtasche/Konturzapfen (CYCLE63/64).........................................................................582
10.5.9
Konturtasche vorbohren (CYCLE64)...................................................................................584
10.5.10
Konturtasche fräsen (CYCLE63)..........................................................................................589
10.5.11
Konturtasche Restmaterial (CYCLE63, Option)...................................................................595
10.5.12
Konturzapfen fräsen (CYCLE63).........................................................................................597
10.5.13
Konturzapfen Restmaterial (CYCLE63, Option)...................................................................602
10.6
Weitere Zyklen und Funktionen...........................................................................................606
10.6.1
Schwenken Ebene / Ausrichten Werkzeug (CYCLE800).....................................................606
10.6.2
Schwenken Werkzeug (CYCLE800)....................................................................................613
10.6.2.1
Ausrichten von Drehwerkzeugen - nur bei G-Code-Programm (CYCLE800)......................613
10.6.2.2
Ausrichten von Fräswerkzeugen - nur bei G-Code-Programm (CYCLE800).......................616
10.6.2.3
Anstellen von Fräswerkzeugen - nur bei G-Code-Programm (CYCLE800).........................617
10.6.3
High Speed Settings (CYCLE832).......................................................................................618
10.6.3.1
Parameter............................................................................................................................621
10.6.4
Unterprogramme..................................................................................................................622
10.7
Weitere Zyklen und Funktionen ShopTurn...........................................................................625
10.7.1
Bohren Mittig........................................................................................................................625
10.7.2
Gewinde Mittig.....................................................................................................................628
10.7.3
Transformationen.................................................................................................................631
10.7.4
Verschiebung.......................................................................................................................633
10.7.5
Rotation................................................................................................................................634
10.7.6
Skalierung............................................................................................................................635
10.7.7
Spiegelung...........................................................................................................................635
10.7.8
Rotation C-Achse.................................................................................................................636
14
Bedienhandbuch, 08/2018, 6FC5398-8CP41-0AA0
Drehen
Werbung
