Siemens SINUMERIK 840D sl Bedienhandbuch Seite 13

9.15.1 Weitere Funktionen in den Eingabemasken........................................................................321
9.15.2 Überprüfung von Zyklenparametern....................................................................................321
9.15.3 Einstelldaten für Technologische Funktionen......................................................................322
9.15.4 Variablenprogrammierung....................................................................................................322
9.15.5 Zyklenaufruf ändern.............................................................................................................322
9.15.6 Kompatibilität bei Zyklenunterstützung...............................................................................323
9.16 Ab-/Anfahrzyklus programmieren.........................................................................................324
9.17 Messzyklenunterstützung.....................................................................................................326
9.18 Beispiel: Standardbearbeitung.............................................................................................327
9.18.1 Werkstückzeichnug..............................................................................................................328
9.18.2 Programmierung..................................................................................................................328
9.18.3 Ergebnisse/Simulationstest..................................................................................................340
9.18.4 G-Code-Bearbeitungsprogramm..........................................................................................342
10 Technologische Funktionen programmieren (Zyklen)..............................................................................345
10.1 Bohren..................................................................................................................................345
10.1.1 Allgemeines..........................................................................................................................345
10.1.2 Zentrieren (CYCLE81).........................................................................................................346
10.1.3 Bohren (CYCLE82)..............................................................................................................348
10.1.4 Reiben (CYCLE85)..............................................................................................................352
10.1.5 Ausdrehen (CYCLE86)........................................................................................................354
10.1.6 Tieflochbohren 1 (CYCLE83)...............................................................................................357
10.1.7 Tieflochbohren 2 (CYCLE830).............................................................................................363
10.1.8 Gewindebohren (CYCLE84, 840)........................................................................................373
10.1.9 Bohrgewindefräsen (CYCLE78)...........................................................................................381
10.1.10 Positionen und Positionsmuster...........................................................................................385
10.1.11 Beliebige Positionen (CYCLE802).......................................................................................386
10.1.12 Positionsmuster Reihe (HOLES1)........................................................................................391
10.1.13 Positionsmuster Gitter oder Rahmen (CYCLE801) .............................................................393
10.1.14 Positionsmuster Kreis oder Teilkreis (HOLES2)..................................................................397
10.1.15 Positionen ein- und ausblenden...........................................................................................403
10.1.16 Positionen wiederholen........................................................................................................405
10.2 Drehen.................................................................................................................................406
10.2.1 Allgemeines..........................................................................................................................406
10.2.2 Abspanen (CYCLE951)........................................................................................................406
10.2.3 Einstich (CYCLE930)...........................................................................................................409
10.2.4 Freistich Form E und F (CYCLE940)...................................................................................412
10.2.5 Gewindefreistiche (CYCLE940)...........................................................................................414
10.2.6 Gewindedrehen (CYCLE99)................................................................................................417
10.2.7 Gewindekette (CYCLE98)....................................................................................................434
10.2.8 Abstich (CYCLE92)..............................................................................................................440
10.3 Konturdrehen.......................................................................................................................442
10.3.1 Allgemeines..........................................................................................................................442
10.3.2 Darstellung der Kontur.........................................................................................................443
10.3.3 Neue Kontur anlegen...........................................................................................................444
10.3.4 Konturelemente erstellen.....................................................................................................446
10.3.5 Passungsmaß eingeben......................................................................................................452
10.3.6 Kontur ändern......................................................................................................................453
10.3.7 Konturaufruf (CYCLE62) - nur bei G-Code-Programm........................................................454
10.3.8 Abspanen (CYCLE952)........................................................................................................455
Drehen
Bedienhandbuch, 08/2018, 6FC5398-8CP41-0AA0
Inhaltsverzeichnis
13