Transport; Storage; Maintenance - Parkside PBRM 39 C2 Originalbetriebsanleitung

1. It is best to tilt the lawnmower backwards. Make sure
that the spark plug (12a) is pointing upwards. If the
spark plug (12a) points downwards, oil can leak out
and cause major damage to the engine and carburettor.
2. Alternatively, you can tilt the device on its side, but you must
make sure that the air filter cover (9) is on the upper side.
3. Clean the underside of the lawnmower with a spatula
and hand brush. The spatula helps to remove coarse
and larger plant debris from the area of the blades (19).
Cleaning the underbody is easier and more thorough
immediately after use. Then dirt and plant residues are
still fresh and can be loosened more easily.
4. If necessary and if the dirt is difficult to remove, you can
also use a special cleaner. Do not use aggressive clean-
ing products such as cold cleaners or white spirit.
5. Check that the grass ejection is clear of grass residues
and remove these if necessary.

14. Transport

m WARNING!
Danger of injury!
Unintended and unexpected start-up of the product may lead
to injuries.
- Switch the engine off before transporting.
- Allow the engine to cool down.
- Remove the spark plug connector (12) from the spark plug
(12a).
IMPORTANT: For transport, the cutting height must always
be set in the highest position.
1. Empty the fuel tank (8) with a petrol suction pump (not
included in the scope of delivery) (see 16.4.).
2. Drain the engine oil from the warm engine (see 16.3).
3. Clean the cooling fins of the cylinder and the housing
(see 13.1.).
4. Fold in the upper push bar (3) (see 15.2.).
5. Wedge a few layers of corrugated cardboard between
the upper push bar (3) and lower push bar (6) and the
engine to prevent any chafing.

15. Storage

m Attention! Do not store the device with the grass collec-
tion basket (16) full. In hot weather, the grass begins to ferment
under heat. There is a risk of fire.
Store the device and its accessories in a dark, dry and frost-
free place that is inaccessible to children. The optimum stor-
age temperature lies between 5 and 30 ˚C.
Store the device in its original packaging.
Cover the device to protect it from dust or moisture. Store the
operating manual with the device.
• Clean and maintain the device before storage.
• Never store the lawnmower with petrol in the fuel tank in-
side a building in which fuel vapours may come into contact
with naked flames or sparks.
• Allow the engine to cool down before you put the lawn-
mower in an enclosed area.
• In the event of prolonged storage, empty the fuel tank with
a petrol suction pump (not included in the scope of delivery)
(see 16.4.).
• In order to avoid fire hazards, keep the engine, exhaust
pipe and the area around the fuel tank free of grass, leaves
and leaking grease (oil).
15.1 Preparing the lawnmower for long-term
storage
m WARNING! Do not remove the petrol in enclosed spac-
es, near fire or when smoking. Petrol fumes can cause explo-
sions and fire.
1. Empty the fuel tank (8) with a petrol suction pump (not
included in the scope of delivery) (see 16.4.).
2. Carry out an oil change (see 16.3).
3. Remove the spark plug connector (12) from the spark
plug (12a). Remove the spark plug (12a) with a spark
plug wrench (not included in the scope of delivery).
4. Fill the cylinder with approx. 20 ml of oil from an oil can.
5. Pull the pull starter (18) slowly so that the oil protects the
inside of the cylinder.
6. Screw the spark plug (12a) back in.
7. Clean the cooling fins of the cylinder and the housing
(see 13.1.).
8. Be sure to clean the entire device to protect the paint.
9. Store the device in a well-ventilated area.
15.2 Folding the upper push bar (3) together
m WARNING!
Risk of jamming!
Always hold the upper push bar (3) with one hand at the high-
est point.
- Never place fingers between the upper push bar (3) and
lower push bar (6).
For space-saving storage, the upper push bar (3) is foldable.
1. Remove the grass collection basket (16).
2. Unhook the pull starter (18) from the cable hook (17).
3. Loosen the star grip nuts (4) on the upper push bar (3)
slightly (do not open completely).
4. Move the upper push bar (3) down. The cables must not
be pinched in the process.

16. Maintenance

m WARNING!
Have maintenance and repair tasks that are not
described in this operating manual, carried out
by a specialist workshop. Use only original spare
parts. There is a risk of accident! Always carry
out maintenance and cleaning work with the en-
gine switched off and the spark plug connector
removed. There is a danger of injury!
Let the device cool down before all maintenance
and cleaning tasks. Elements of the engine are
hot. There is a danger of injury and burning!
GB 45