Before Commissioning - Parkside PBRM 39 C2 Originalbetriebsanleitung

• Household wipes (to wipe up oil/petrol residue; dispose of
these at a filling station)
• A petrol extraction pump
• An oil can with hand pump
• Pliers
• Phillips screwdriver
• Slotted-head screwdriver
• Open-end wrench/socket spanner
9.1 Installation of the lower push bar (6) (Fig. 3)
m Attention! Make sure that the throttle cable is not
squeezed when mounting the push bars (3+6).
1. Fit the two lower push bars (6) in the holes provided.
2. Fasten each of these with a 4.0 x 12 mm screw (C). Ensure
that the pull cord, which will be fastened later with a cable
clip (5), and the Bowden cable are not in the way (Fig. 6).
9.2 Mounting the upper push bars (3) and at-
taching the pull starter (18) (Fig. 4, 5, 6)
1. Screw the upper push bar (3) to the lower push bar (6) with
an M8 bolt (A), a washer (B) and a star grip nut (4) on the
left side (Fig. 4).
2. Then screw the upper push bar (3) on the right side to the
lower push bar (6) with an M8 bolt (A), the cable pull hook
(17), a washer (B) and a star grip nut (4) (Fig. 5).
3. Hook the handle of the pull starter (18) into the cable hook
(17) (Fig. 5).
4. Fix the cable pull with the enclosed cable clip (5) to the
lower push bar (6) (Fig. 6).
9.3 Fitting the wheels (Fig. 7+8)
1. Unscrew the pre-assembled wheel bolts (11b) together
with the wheel shims (11c) with an open-end spanner AF
21 and put them aside.
2. Remove the wheel cap (11a) on the wheel (11) with a
screwdriver if necessary (Fig. 8).
3. Now fit a wheel washer (11c), a wheel (11) and a wheel
bolt (11b) into the thread with the desired cutting height.
You can choose between a cutting height of 30 - 66 mm.
ATTENTION:
Note the marking on the head of the wheel bolt (11b) (L =
left-handed thread, R = right-handed thread)
4. Fit the wheels (11) at the same cutting height.
5. Put the wheel caps (11a) back on the wheels (11).

10. Before commissioning

ATTENTION!
Always make sure the device is fully assembled
before commissioning!
WARNING!
Health hazard!
Inhalation of petrol/lubricating oil vapours and exhaust gas-
es can cause serious damage to health, unconsciousness and
in extreme cases death.
- Do not breathe petrol/lubricating oil vapours and exhaust
gases.
- Operate the product outdoors only.
42 GB
NOTE!
Product damage
Using the product without or with too little engine and gear-
box oil can result in engine damage.
- Fill with petrol and oil before commissioning. The product is
supplied without engine and gearbox oil.
NOTE!
Environmental damage!
Spilled oil can pollute the environment permanently. The liq-
uid is highly toxic and can quickly lead to water pollution.
- Fill/empty oil only on level, paved surfaces.
- Use a filling nozzle or funnel.
- Collect drained oil in a suitable container.
- Wipe up spilled oil carefully immediately and dispose of
the cloth according to local regulations.
- Dispose of oil as per local regulations.
NOTE!
Risk of damage!
If incorrectly stored or undrained fuel is used, the carburettor
may become clogged or engine operation may be affected.
- Put unused fuel in an airtight vessel and store it in a dark,
cool room.
Check before operation
• Check all sides of the engine for oil or fuel leaks.
• Check the engine oil level.
• Check the fuel level - the tank should contain at least 0.4L.
• Check the air filter condition (see section 16.5).
• Check the condition of the fuel lines.
• Make sure that the spark plug connector (12) is attached to
the spark plug (12a).
• Look for signs of damage.
• Check that all protective covers are in place and all screws,
nuts and bolts are tightened.
10.1 Filling up with engine oil (Fig. 9)
m Attention!
The lawnmower is delivered without engine oil.
Therefore, ensure that you add oil before starting
it up. Use multigrade oil (SAE 10W-30 or 10W-40)
for this.
Check the oil level every time before commissioning. An oil
level that is too low can damage the engine.
1. Place the lawnmower on a level, even surface.
2. Unscrew the oil dipstick (14).
3. Fill the tank with engine oil (SAE 10W-30/SAE 10W-40)
using a funnel (not included in scope of delivery). Note
the max. filling capacity of 400 ml. Carefully fill the oil up
to the lower edge of the filling nozzle.
4. Wipe the oil dipstick (14) with a clean, lint-free cloth.
5. Re-insert the oil dipstick (14) and pull it out again. Check the oil
level without screwing the oil dipstick (14) back in.
6. The oil level must be within the middle mark on the oil
dipstick (14).
7. If the oil level is too low, add the recommended amount of
engine oil (max. 400 ml).
8. Then screw the oil dipstick (14) in again.