Residual Risks; Technical Data; Before Commissioning - Scheppach CSP49-4T Original Bedienungsanleitung

■ Make sure that there are no nails or metal pieces
in the cutting area. Pay special attention to nails or
pieces of iron around the cutting area. Also be care-
ful when sawing hardwoods where the chain can
get caught. This can cause kick-back.
■ Start cutting at full power and always keep the
chainsaw at maximum speed while sawing.
■ Make sure that there are no objects on the floor that
you can trip over.

6.9 Residual risks

m DANGER
RISK OF INJURY !
Contact with the saw chain can lead to fatal cuts.
Never touch the saw chain with your hands while it is
running.
RISK OF KICK-BACK !
Kick-back can lead to fatal cuts.
DANGER OF BURNING !
The chain and guide bar heat up during operation.

7. Technical data

Weight unfuelled, without cutting gear approx. ..5,3 kg
Weight unfuelled, with cutting gear approx. ......6,0 kg
Fuel tank ................................. approx. 400 cm
Fuel..............................................................................
Normal petrol / Lead free max. 10% bioethanol
Engine oil / quantity / type ...........................................
ca. 100 cm³ (0,1 l) / 10W30 / SAE30
Tank for chain lubricating oil ... approx. 300 cm
Usable cutting length* /
Guide rail .................................................. 35 cm (16")
Max. chain speed ..........................................18,1 m/s
Chain pitch......................................... 9,525 mm (3/8")
Driving link thickness ....................... 1,27 mm (0.050")
Type of saw chain
(pre-assembled): ........................................ 91PJ057X
Type of guide bar
(pre-assembled): ..................................160SDEA041
Chain wheel tooth pitch ....... 6 teeth / 9,525 mm (3/8")
Engine displacement ........................................49 cm
Max. engine power output per ISO 7293 ......... 1,6 kW
Idle speed n ...................................... 3000 ± 300 rpm
0
Speed n ................................................... 9500 rpm
max
Spark plug ......................................................CMR5H
* The actual cutting length may be less than the spec-
ified cutting length.
Noise
Sound pressure level L
Uncertainty K
Sound power level L
per ISO 22868 ....................................... 109,09 dB(A)
Uncertainty K
Wear hearing protection.
Excessive noise can result in a loss of hearing.
The specified device emissions values have been
measured in accordance with a standardised test pro-
cedure and can be used for the comparison of one
tool with another.
The specified noise emission values can also be used
for an initial estimation of the exposure.
Vibration
Vibration value at the rear
Handle per ISO 22867 ................................9,396 m/s
Vibration value at the front
Handle per ISO 22867 ..............................10,589 m/s
Uncertainty K ..................................................1.5 m/s
m WARNING
Avoid the risks associated with vibration, e.g. the risk
of white finger syndrome (circulatory disorders) by
(0,4 l) taking frequent breaks from work where you rub your
3
palms together, for example.

8. Before commissioning

(0,3 l)
3
• Open the packaging and carefully remove the de-
• Remove the packaging material, as well as the
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
OREGON
• If possible, keep the packaging until the expiry of
OREGON
ATTENTION
The device and the packaging are not children's toys!
Do not let children play with plastic bags, films or small
3
parts! There is a danger of choking or suffocating!
 www.scheppach.com
per ISO 22868 101,28 dB(A)
pA
................................................. 2,5 dB
pA
WA
............................................... 0,61 dB
WA
vice.
packaging and transport safety devices (if present).
damage.
the warranty period.
2
2
2
GB | 33