Parkside PMTS 210 A1 Originalbetriebsanleitung Seite 13

c) Never hold and press the workpiece that is be-
ing cut off against the rotating saw blade. Press-
ing the workpiece being cut off against the saw blade will
create a binding condition and kickback.
d) Align the fence to be parallel with the saw
blade. A misaligned fence will pinch the workpiece
against the saw blade and create kickback.
e) Use a featherboard to guide the workpiece
against the table and fence when making non-
through cuts such as rabbeting, dadoing or re-
sawing cuts. A featherboard helps to control the work-
piece in the event of a kickback.
f) Use extra caution when making a cut into blind
areas of assembled workpieces. The protruding
saw blade may cut objects that can cause kickback.
g) Support large panels to minimise the risk of
saw blade pinching and kickback. Large panels
tend to sag under their own weight. Support(s) must be
placed under all portions of the panel overhanging the
table top.
h) Use extra caution when cutting a workpiece
that is twisted, knotted, warped or does not
have a straight edge to guide it with a mitre
gauge or along the fence. A warped, knotted, or
twisted workpiece is unstable and causes misalignment of
the kerf with the saw blade, binding and kickback.
i) Never cut more than one workpiece, stacked
vertically or horizontally. The saw blade could pick
up one or more pieces and cause kickback.
j) When restarting the saw with the saw blade
in the workpiece, centre the saw blade in the
kerf so that the saw teeth are not engaged in
the material. If the saw blade binds, it may lift up the
workpiece and cause kickback when the saw is restarted.
k) Keep saw blades clean, sharp, and with suffi-
cient set. Never use warped saw blades or saw
blades with cracked or broken teeth. Sharp and
properly set saw blades minimise binding, stalling and kick-
back.
Table saw operating procedure warnings
a) Turn off the table saw and disconnect the pow-
er cord when removing the table insert, chang-
ing the saw blade or making adjustments to
the riving knife or saw blade guard, and when
the machine is left unattended. Precautionary meas-
ures will avoid accidents.
b) Never leave the table saw running unattended.
Turn it off and don't leave the tool until it comes
to a complete stop. An unattended running saw is an
uncontrolled hazard.
c) Locate the table saw in a well-lit and level area
where you can maintain good footing and bal-
ance. It should be installed in an area that pro-
vides enough room to easily handle the size of
your workpiece. Cramped, dark areas, and uneven slip-
pery floors invite accidents.
d) Frequently clean and remove sawdust from
under the saw table and/or the dust collection
device. Accumulated sawdust is combustible and may
self-ignite.
e) The table saw must be secured. A table saw that is
not properly secured may move or tip over.
f) Remove tools, wood scraps, etc. from the table
before the table saw is turned on. Distraction or a
potential jam can be dangerous.
g) Always use saw blades with correct size and
shape (diamond versus round) of arbour holes.
Saw blades that do not match the mounting hardware of the
saw will run off-centre, causing loss of control.
h) Never use damaged or incorrect saw blade
mounting means such as flanges, saw blade
washers, bolts or nuts. These mounting means were
specially designed for your saw, for safe operation and
optimum performance.
i) Never stand on the table saw, do not use it as a
stepping stool. Serious injury could occur if the tool is
tipped or if the cutting tool is accidentally contacted.
j) Make sure that the saw blade is installed to ro-
tate in the proper direction. Do not use grinding
wheels, wire brushes, or abrasive wheels on a
table saw. Improper saw blade installation or use of ac-
cessories not recommended may cause serious injury.
Safety instructions for the handling of saw blades
1. Only use insertion tools if you have mastered their use.
2. Observe the maximum speed. The maximum speed speci-
fied on the insertion tool may not be exceeded. If specified,
observe the speed range.
3. Observe the motor / saw blade direction of rotation.
4. Do not use any insertion tools with cracks. Sort out cracked
insertion tools. Repairs are not permitted.
5. Clean dirt, grease, oil and water off of the clamping sur-
faces.
6. Do not use any loose reducing rings or bushes to reduce
holes on circular saw blades.
7. Make sure that fixed reducer rings for securing the inser-
tion tool have the same diameter and have at least 1/3 of
the cutting diameter.
8. Make sure that fixed reducer rings are parallel to each
other.
9. Handle insertion tool with caution. They are ideally stored
in the originally package or special containers. Wear pro-
tective gloves in order to improve grip and to further reduce
the risk of injury.
10. Prior to the use of insertion tools, make sure that all protec-
tive devices are properly fastened.
11. Prior to use, make sure that the insertion tool meets the
technical requirements of this power tool and is properly
fastened.
12. Only use the supplied saw blade for cutting wood, never
for the processing of metals.
13. Use the correct saw blade for the material to be processed.
14. Use only a saw blade with a diameter that matches the
specifications on the saw.
GB/IE 7