Operation With A Pc; Main Menu; Submenus; Key 1 : Installed Components - Monacor MEVAC-4 Bedienungsanleitung

9 Operation with a PC

Use a null modem cable to connect MEVAC-4 to the serial
interface (e. g. COM1) of a PC. Start the communications
program (e. g. Windows HyperTerminal) with the following
parameters (interface settings):
Windows is a registered trademark of Microsoft Corporation in the United States
and other countries.
Parameter
Bits per second
Data bits
Stop bits
Parity
Protocol (flow control)
Fig. 121 Interface settings
The keys mentioned in this chapter refer to the keys of
the PC keyboard!

9.1 Main menu

Once the connection has been established, press the key [i] to
call up the main menu:
MEVAC4

KEY 1 : installed components

KEY 2 : Audio level
KEY 3 : Audio and Relaisprogramming
KEY 4 : Misc. Setting
KEY 5 : Text input
KEY 6 : Errors (= indication of the current status)
KEY 7 : Factory Setting
Caution !! Delets all Settings
Fig. 122 Main menu
Settings can be made via the menus called up
with the keys 2 – 5.

9.2 Submenus

Press the keys [1] to [7] to go to the submenus.
Note: The followings menu illustrations are just examples.
9.2.1 Key [1] – Installed components
INSTALLED COMPONETS
ALARM 1 3,4V
ALARM 2 3,4V
FIRE MIC1 3,3V COIL: INSTALLED
FIRE MIC2 3,3V COIL: INSTALLED
OUT: 1 LINE: 1
LINE: 2
LINE: 3
OUT: 2 LINE: 4
SPARE AMP INSTALLED
BATT. VOLTAGE : 24V
Fig. 123 Submenu "Installed components"
42
Setting
9600
8
1
None
None
A:012 B:008
A:031 B:057
A:009 B:010
A:009 B:013
9.2.2 Key [ 2 ] – Level
LEVEL
SOURCE | LINE1 | LINE2 | LINE3 | LINE4 |
___________________________________________
a MUSIC 1 |−06 dB |−07 dB |−16 dB | −− dB |
b MUSIC MA |−28 dB |−12 dB |−12 dB |−12 dB |
c CHIME |−06 dB |−06 dB |−06 dB |−06 dB |
d AUX |−06 dB |−06 dB |−06 dB |−10 dB |
e MESSAGE | −− dB |−06 dB |−06 dB |−06 dB |
f VOLUME |−10 dB |−06 dB |−06 dB |−06 dB |
g BASS | 00 dB | 00 dB | 00 dB | 00 dB |
h TREBLE | 00 dB | 00 dB | 00 dB | 00 dB |
i SYS 4/2 | 00 dB | 00 dB | 00 dB | 00 dB |
j ALARM 1 |−12 dB |−06 dB |−06 dB |−06 dB |
k ALARM 2 |−12 dB |−06 dB |−06 dB |−06 dB |
l FIRE MIC |−12 dB |−06 dB |−06 dB |−06 dB |
m F. CHIME |−12 dB |−06 dB |−06 dB |−06 dB |
Fig. 124 Submenu "Level"
To select the value to be changed, enter the letter that is
shown at the beginning of the respective line. Use the keys
[ + ] and [ – ] to change the value; use the tab key [  ] to go to
the next value in the next column. To confirm and exit, press
the key [ENTER].
9.2.3 Key [ 3 ] – Audio and relay programming
Attention: Sources for which no zone and no relay have been
activated will not be shown.
SOURCE | Z1 | Z2 | Z3 | Z4 || R1 | R2 | R3 | R4 |
a SYS 4/2 01| ** |
b SYS 4/2 02| | ** |
c SYS 4/2 03| |
d SYS 4/2 04| |
e ALARM 1 | ** | ** | ** | ** ||
f ALARM 2 | ** | ** | ** | ** ||
g CHIME | ** | ** | ** | ** ||
h AUX | ** | ** | ** | ** ||
i FIRE MIC1 | ** | ** | ** | ** ||
j FIRE MIC2 | ** | ** | ** | ** ||
k MESSAGE | ** | ** | ** | ** ||
Fig. 125 Submenu "Audio and Relay Programming"
To select the signal source to be changed, enter the letter that
is shown at the beginning of the respective line. Use the keys
[ + ] and [ – ] to change the setting; use the tab key [  ] to go
the next setting in the next column. To confirm and exit, press
the key [ENTER].
9.2.4 Key [ 4 ] – Other settings
(chime, test routines)
Also see chapter 7.4.
a CHIME
b SHORT TO EARTH
c IMPEDANCE
d SHORT CIRCUIT
e OPEN LINE
f PILOT LEVEL
g AUTO ERROR OUTPUT
h IMP TOLERANCE
Fig. 126 Submenu "Other Settings"
To select the setting to be changed, enter the letter that is
shown at the beginning of the respective line. Use the keys
[ + ] and [ – ] to change the setting; use the tab key [  ] to go
to the next setting in the next column. To confirm and exit,
press the key [ENTER].
| | || | |
| || | |
| ** | || | |
| | ** || | |
| |
| |
| |
| |
| |
| |
| |
ON
LINE: 4 ** 3 ** 2 ** 1 **
LINE: 4 ** 3 ** 2 ** 1 **
LINE: 4 ** 3 ** 2 ** 1 **
LINE: 4 ** 3 ** 2 ** 1 **
049 V
OFF
NORMAL (7)
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |