Switching The Machine Off - PAVONI ITALIA MINITEMPER Bedienungsanleitung

18 | EN
• replace the cover.
To speed up the work cycle, you can pour the preheated product into the basin (max 35 °C).
CAUTION:
please do not add any more chocolate till the machine has completed the tempering cycle.
Starting the work cycle (start)
Having chosen the program and adding the product to the basin, simply press Start (see keyboard). The
heating lamps inside the machine now start to heat up. The temperature is shown on the display; this rises
gradually until the set SP1 (1st level) value is reached. The display constantly shows the temperature of the
chocolate throughout the work cycle.
Start work cycle (basin rotation)
1st stage (heating)
The basin starts rotating once the 1st level temperature SP1 has been reached. The temperature remains
constant in the basin for pause PA1.
2nd stage (cooling)
The cooling fan now starts to cool the chocolate to the SP2 temperature. The temperature is then kept
constant thanks to the lamps during pause PA2.
3rd stage (final heating)
The temperature starts rising again (thanks to the heating lamps) until it reaches the set SP3 value. The
temperature is then kept constant during pause PA3
End work cycle
The work cycle ends once the 3rd stage in the program has been completed. The basin continues to turn;
the machine buzzer sounds. The word end (flashing) appears on the display with the final temperature SP3.
After the work cycle
Press the ON/OFF button (see keyboard) to silence the buzzer and stop the basin from rotating. Press the
ON/OFF button again to start the basin turning and keep the temperature constant at the SP3 (3rd stage
level). Press the ON/OFF button to stop.
Note: you can always check the stage during the work cycle by pressing key P. The display will show the
stage for 3 seconds: e.g. SP2 (with temperature level 2) PA2 (with pause 2). You can interrupt the work cycle
by pressing the "start" key. The cycle is reset while the program type is still that saved and shown on the
display. Press the button (04) on the right of the machine to mix and amalgamate the product better during
heating (or when the product is hotter than 35 °C.

Switching the machine off

After using the machine, flip the ON/OFF switch (03) to "O" and then unplug the power cable (07).
Autotest
The "autotest" function lets you check the condition of the various machine components.
The procedure involved:
• hold the "start" key down and press the "ON/OFF switch" (03);
• the word TES appears on the keyboard display.
You can now:
a) press "I O" (ON/OFF) to check the motor; press again to stop;
b) press "start" to switch on the lamps; press again to switch off;
c) press "P" to switch on the fan; press again to switch off.
You need to switch the machine off in order to quit this programming mode.
Changing the basin
Removal
Switch the machine off by turning the red "ON/OFF switch" (03) to "O" (on the right of the machine).
Unplug the "male" plug (07) from the mains socket (machine not powered up). Remove the cover (05).
Extract the temperature probe (10) from its seat (11) on the dividing wall (08). Loosen the two threaded
knobs (09) so that the two curved side sections on the dividing wall come away from their columns. Turn the
dividing wall (08) anti-clockwise to separate from the columns. Remove the dividing wall (08). Extract the
basin (12).
Repositioning
Make sure that the "male" plug (07) on the power cable is not plugged into the mains socket (machine not
powered up). Make sure that the basin (12) and the dividing wall (08) are clean and dry (we recommend
washing with hot water). Place the basin in the machine by positioning the three pins in the holes on the
motor rotation disk. Add the dividing wall (08), making sure that the two curved side sections fit on the
columns. Tighten the two threaded knobs (09) on the columns to secure the dividing wall. Introduce the
probe (10) in its seat (11) on the side of the dividing wall. The machine can now be switched on again and
programmed for a new work cycle.
Machine without cover
• dividing wall (08)
• knurled knob (09)
• temperature probe (10)
• seat for temperature probe (11)
• basin (12)
EN | 19