Installation - Scheppach BCAG125-20ProS Original Bedienungsanleitung

9.2 Adjusting the guard (Fig. 4)
• Adjust the guard (1) to protect your hands so that
the material being ground is directed away from
your body.
• The position of the guard (1) can be adjusted to any
specific working conditions. Undo the clamp handle
(c) and turn the cover into the required position.
• Ensure that the guard (1) correctly covers the gear
wheel casing.
• Secure the clamp handle (c) again.
• Ensure that the guard (1) is secure.
m Take care that the safety device is secure.
m Never use the angle grinder without the guard.
9.3 Test run for new grinding wheels
• Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
fitted in place.
• Replace vibrating wheels immediately.

10. Installation

m Warning
Wear protective goggles.
m Important
You must fully assemble the appliance before using it
for the first time!
10.1 Battery
To ensure that the Li battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you notice
that the power of the cordless equipment drops.
10.1.1 Removing/inserting the battery
• To remove the battery (8) from the appliance, press
the release button on the battery and pull out the
battery.
• To insert the battery (8), place it on the guide track
and push it back into the appliance. It will audibly
snap in.
10.1.2 Used batteries
If a fully recharged battery lasts for considerably
shorter operating times, the battery is used up and
needs to be replaced. Only use an OEM battery pack
replacement available from our Customer Service
10.2 Switches (Fig. 1)
The angle grinder is equipped with a safety switch (3)
for accident prevention and an on/off switch (4).
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
10.2.1 Switching on
To switch on the machine, push the safety switch (3)
forward and press the on / off switch (4).
ATTENTION
Wait until the machine has reached its top speed. You
can then position the angle grinder on the workpiece
and machine it.
10.2.2 Switching off
m CAUTION
Risk of injury! The wheel continues to rotate.
In order to turn off the machine, release the safety
switch (3) and the on/off switch (4).
10.3 Changing the grinding wheels (Fig. 4, 5)
Use the face spanner (5) supplied to change the
grinding wheels. The face spanner (5) is stored in the
additional handle (6). Pull the face spanner (5) out of
the additional handle (6) when you need it.
m WARNING
For safety reasons, the angle grinder must not
be operated with the face spanner (5) inserted in
it.
m WARNING
Always pull out the battery pack before starting
any cleaning work.
10.3.1 Simple wheel change by spindle lock
NOTICE
Only ever press the spindle lock when the motor
and grinding spindle are at a standstill! You must
keep the spindle lock pressed while you change
the wheel!
• Press the spindle lock (2) and allow the grinding
wheel (7) to latch in place.
• Open the flange nut (b) with the face spanner (5).
• Change the grinding or cutting wheel and tighten
the flange nut with the face spanner (5).
For grinding or cutting wheels up to approx. 3
mm thick:
Screw on the flange nut with the flat side facing the
grinding or cutting wheel.
10.3.2 Flange arrangements when using grinding
wheels and cutting wheels (Fig. 5)
• Mount guard (1), clamping flange (a), wheel (7) and
flange nut (b) as shown in Fig. 5.
• The arrows indicate the mounting direction.