Intended Use; Installation - Scheppach CFS135-20Li Original Bedienungsanleitung

performs optimally.
• Hands may never enter the processing zone when
the machine is in operation.

9. Intended use

The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also observe
the safety information, the assembly instructions and
the operating instructions to be found in this manual.
All persons who use and service the equipment have
to be acquainted with this manual and must be in-
formed about the equipment's potential hazards.
It is also imperative to observe the accident preven-
tion regulations in force in your area.
The same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any changes
made to the equipment nor for any damage resulting
from such changes.
The machine may be used only with original acces-
sories and original tools of the manufacturer.
The safety-, workplace- and maintenance specifica-
tions of the manufacturer as well as the dimensions
specified in the technical data must be observed.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.

10. Installation

m IMPORTANT!
You must fully assemble the appliance before
using it for the first time!
To ensure that the Li battery pack provides long ser-
vice you should take care to recharge it promptly.
You must recharge the battery pack when you notice
that the power of the cordless equipment drops.
Caution! Make sure that the device is switched off
before you connect it to the mains supply.
Note! Always switch on the delta sander before
bringing it into contact with the workpiece material.
Switching on the device:
Move the ON / OFF switch (8) downwards into the
"ON" position.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Switching off the device:
Move the ON / OFF switch (8) upwards into the "OFF"
position.
Vacuum dust extraction
Warning! Danger of fire! There is the danger of fire
when working with electrical devices that have a dust
box or can be connected to a vacuum cleaner. Under
certain conditions the wood dust in the dust extrac-
tion bag (or in the vacuum's dust bag) may ignite, e.g.
as a result of flying sparks generated when abrading
metals or metal objects left in wood. This can hap-
pen particularly if the wood dust is mixed with paint
residue or other chemicals and the abraded parti-
cles are hot from prolonged abrasion. Therefore you
must empty the device's dust collection box and the
vacuum cleaner's dust bag before taking a break or
stopping work and always avoid overheating of the
abraded particles and the device.
Wear a dust mask!
Warning ! Always pull the mains plug is out of the
socket before doing any work on the device.
Dust box for internal vacuum extraction
Connection:
Push the dust box for internal vacuum extraction (4)
on to the hand-held sander until it engages.
Removal:
Press the release button (5) of the dust extraction
box for internal vacuum extraction (4) and withdraw it
towards the rear of the device.
Note: Always empty the dust collection box (4) in due
time and shake any remaining dust out; this will en-
sure optimal vacuum performance.
Attaching / detaching sanding sheets
Warning! Always pull the mains plug is out of the
socket before doing any work on the device.
Attaching:
Sanding sheets are attached to the backing plate (7)
by means of the hook and pile fastening.
Detaching:
Simply pull the sanding sheet off the backing plate (7)
(see Fig. C).
Sanding and surfaces:
The sanding output and the quality of the surface fin-
ish are determined by the grade of grit on the sanding
sheet.
Always use sanding sheets with grades that are suit-
able for the particular surface you are sanding.
21 | GB