Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
keys always remain activated.
To once again activate all the beeps
that accompany each action, again
simultaneously press the touch key
(11) and the locking touch key
for three seconds. The time indicator
(12) will display "On".
Stop&Go Function
This function puts the cooking process
on pause. The timer will also be
paused if it is activated.
Activating the Stop&Go function.
Touch the Stop &Go sensor
.The power indicators will show the
symbol
to indicate cooking has
been paused.
Deactivating the Stop&Go function
Touch Stop&Go sensor
The cooking is resumed under the
same power and timer settings that
were established before the pause.
Power Function
This function supplies "extra" power
to the plate, above the nominal value.
Said power depends on the size of the
plate, with the possibility of reaching
Table 1
MINIMUM DIAMETER OF THE VESSEL'S BOTTOM
FOR ANY COOKING ZONE
(depending
on model)
the maximum value permitted by the
generator.
1 S l i d e t h e f i n g e r a b o v e t h e
corresponding cursor slider (2)
until the power indicator (3) shows
(6)
"9" and keep the finger pressed for
one second, or touch directly on "P"
and keep pressed the finger for one
second.
2 The power level indicator (3) will
show the symbol P, and the plate
will start to supply extra power.
The Power function has a maximum
duration specified in Table 1. After this
time, the power level will automatically
adjust to 9. A beep sounds.
(6)
Deactivation of Power Function,
before its working time passes, can
be done either by means of touching
cursor "slider" modifying its power level
or repeating step 3.
(6) again.
Timer Function
(countdown clock)
This function facilitates cooking given
that you don't have to be present: You
can set a timer for a plate, and it will
turn off once the desired time is up.
F o r t h e s e m o d e l s , y o u c a n
simultaneously program each plate for
durations ranging from 1 to 90 minutes.
centered
2 points
on 1 point
covered
8 cm
19 cm
-
15 cm
Setting a timer on a plate.
Once the power level is set on the
desired zone, and while the decimal
dot of the zone keeps on, the zone
will be able to be timed.
To that end:
1 Touch sensor
Timer Indicator (12) will show "00"
and corresponding zone indicator
(3) will show the symbol
alternately with its current power
level.
2 Immediately afterwards set a
cooking time between 1 and 99
minutes, using the sensors
ó
value will start at 60, whereas with
the second it will start at 01. By
keeping sensors
pressed, the value will be restored
to 00. When there is less than one
minute left, the clock will begin to
count down in seconds.
3 . When the timer indicator (12) stops
flashing, it will start to count down
the time automatically. The indicator
(3) relating to the timed hotplate
will alternately display the selected
power level and the symbol
Once the selected cooking time has
elapsed, the heating zone being timed
is turned off and the clock emits a
series of beeps for several seconds.
To turn off the audible signal, touch
any sensor.The timer indicator (12)
will display a flashing 00 beside of
the decimal dot (4) of the selected
zone. If the heating zone turned off is
hot, its power indicator (3) will display
4 points
alternately the H symbol and a "-".
vertical
covered
If you wish to time another hotplate
at the same time, repeat steps 1 to 3.
24 cm
If one or more zones are already
timed, the timer indicator (12) will
show by default the shortest remaining
time to finish, showing a "t" on the
related zone. Rest of timed zones will
show on their corresponding indicator
-
zones the decimal dot blinking. When
cursor "slider" of another timed zone
is pressed, the timer will show the
remaining time of that zone for a few
seconds and its indicator will show
EN
(10) or
(11).
blinking
(11). With the first one the
(10) ó
35
(10)
(11)
,.
Werbung
Inhaltsverzeichnis
