Safety Switch Off Function; Suggestions And Recommendations; Cleaning And Maintenance - Teka AFF-Serie Bedienungsanleitung

EN
Flex Zone function
Through this function, it is possible
to enable two cooking zones work
together, and to select a power level
and to activate the timer function for
both zones.
To activate this function, press the
/
sensor (14). By doing so, the
decimal points (4) of the linked plates
will light up and the value "0" will be
shown on their power indicators (3).
The clock timer indicator (12) will
show three segments indicating the
activated zones. In case your model
has several zones with "Flex Zone",
you can select the desired option
by pressing the sensor
before assigning the power to the
chosen zone. You will have a few
seconds to perform the next operation;
otherwise, the function will be disabled
automatically.(see fi g 7).
After the "Flex Zone" is selected, you
can assign the power by touching
any of the "sliders" cursors (2) of
one of the linked zone. The power
level and its variations are displayed
simultaneously on the power indicators
(3) of both zones.
To disable this feature, you should
/
touch the sensor
Also, when the function is disabled,
the levels of powers and functions
assigned to the related zones are
cleared.
Safety switch off function
If due to an error one or several
heating zones do not switch off , the
appliance will be automatically discon-
nected after a set amount of time (see
table 1).
Table 1
Selected MAXIMUN
power OPERATING TIME
level (in hours)
0
1
2
3
46
4
5
6
7
8
9
P
When the "safety switch off " function
has been triggered, a 0is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Keep the control panel of the
heating areas clean and dry at all
times.
/
(14)
In the event of operating pro-
blems or incidents not mentioned in
this manual, disconnect the
appliance and contact the TEKA
technical service.
Suggestions and
recommendations
* Use pots or pans with thick, comple-
tely fl at bottoms.
* Do not slide pots and pans over the
glass because they could scratch it.
(14) again.
* Although the glass can take knocks
from large pots and pans without
sharp edges, try not to knock it.
* To avoid damaging the ceramic
glass surface, do not drag pots and
pans over the glass and keep the
undersides of them clean and in
good condition.
* Recommended diameters of the pot
bottom (see ''Technical Data Sheet''
supplied with the product).
Try not to spill sugar or pro-
ducts containing sugar on the glass
as while the surface is hot these
could damage it.
0
8

Cleaning and maintenance

8
5
To keep the appliance in good condition,
clean it using suitable products and
implements once it has cooled down.
4
This will make the job easier and avoid
4
the build-up of dirt. Never use harsh
3
cleaning products or tools that could
scratch the surface, or steam-operated
2
equipment.
2
1
Light dirt not stuck to the surface can
10 or 5 minutes,
be cleaned using a damp cloth and a
readjusts to level 9
(depending on model)
gentle detergent or warm soapy water.
However, for deeper stains or grease
use a special cleaner for ceramic hot
plates and follow the instructions on
the bottle. Dirt that is fi rmly stuck due
to being burned repeatedly can be
removed using a scraper with a blade.
Slight tinges of colour are caused by
pots and pans with dry grease residue
underneath or due to grease between
the glass and the pot during cooking.
These can be removed using a nickel
scourer with water or a special cleaner
for ceramic hot plates. Plastic objects,
sugar or food containing a lot of sugar
that have melted onto the surface
must be removed immediately using
a scraper.
Metallic sheens are caused by dragging
metal pots and pans over the glass.
These can be removed by cleaning
thoroughly using a special cleaner
for ceramic glass hot plates, although
you may need to repeat the cleaning
process several times.
Warning:
stuck to the glass due to a product
having melted between them. Do not
try to lift the pot while the heating
zone is cold! This could break the
glass.
on it as it could break and cau-se
injury. Do not use the glass as a
surface for placing objects.
TEKA INDUSTRIAL S.A. reserves the
right to make changes to its manuals
that it deems necessary or useful,
A pot or pan may become
Do not step on the glass or lean