Stop&Go Function; Power Function - Teka IT 6450 IKNOB Montageanleitung Und Empfehlungen Zur Verendung Und Wartung

EN
If a pan is not placed within this time
period, or the pan is unsuitable, the
cooking zone shuts off.
When finished, turn off the
cooking zone by using the knob.
Otherwise an undesired operation
could occur if a pan is accidentally
placed on the cooking zone during
the three minutes. Avoid possible
accidents!
Lock Function
With the "Block" function, you can
block the other sensors, except for the
on/off sensor (1), in order to avoid
undesired operations. This function is
useful as a childproof safety.
Activating the function.
To activate this function, touch sensor
(6) for at least one second. The
icon (6) will be illuminated with
higher intensity indicating that the
control panel is blocked. To deactivate
the function, just touch sensor
(6) again. The icon
illuminated fainter.
Deactivating the function.
If the on/off sensor
to turn off the appliance while the
"Block" function is activated, it won't
be possible to turn the hob on again
until it gets unlocked. When the hob
is switched off and "Block" function
is activated, lock icon
off general sensor (1) will remain
illuminated around 1 minute. After that
they will be off. Trying to switch on the
hob in this condition, lock icon
will be illuminated again, showing the
hob remains locked.
Silencer of the beep
Immediately after switching on the
hob, if "Timer" sensor
"Stop&Go" sensor (7) are pressed
simultaneously for three seconds,
the beep that accompanies each
action will be deactivated. The power
indicators (4) will display "OF".
This deactivation will not be applied
24
to all the functions, as for example the
beep for on/off, the ending of the timer
or the locking/unlocking of the touch
keys always remain activated.
In order to activate again the beeps that
accompanies each action, press again
simultaneously "Timer" sensor
and "Stop&Go" sensor
seconds. The power indicators (4) will
display "On"
Stop&Go Function
This function puts the cooking process
on pause. The timer will also be
paused if it is activated.
Activating the function.
Touch "Stop&Go" sensor
Its icon
with higher intensity and the power
indicators (4) will show the symbol
to indicate cooking has been paused.
Deactivating the function.
Touch "Stop&Go" sensor
(6) will be
Its icon
and cooking resumes under the same
power and timer settings that were
established before the pause.
(1) is used

Power Function

This function supplies "extra" power
to the plate, above the nominal value.
(6) and on/
Said power depends on the size of the
plate, with the possibility of reaching
the maximum value permitted by the
generator.
(6)
1 Twist the knob (2) rightwards
until power level 9 and wait for
a second. Twist the knob again
rightwards until a P is shown in its
corresponding power indicator (4).
2 The power level indicator (4) will
(8) and
show the symbol P, and the plate
will start to supply extra power.
The "Power" function has a maximum
duration specified in Table 1. After this
time, the power level will automatically
adjust to 9. A beep sounds.
(8)
(7) for three
(7).
(7) will be illuminated
(7) again.
(7) will be illuminated fainter
On activating the "Power" function in
one hotplate, it is possible that the
performance of some of the others
may be affected, reducing its power to
a lower level, in which case this will be
displayed on its indicator (4).
Deactivation of "Power" function,
before its working time finishes, twist
the knob (2) and choose a different
power level.
Timer Function
(countdown clock)
This function facilitates cooking given
that you don't have to be present: You
can set a timer for a plate, and it will
turn off once the desired time is up.
F o r t h e s e m o d e l s , y o u c a n
simultaneously program each plate
for durations ranging from 1 to 90
minutes.
Timing one plate.
Once the power level is set on the
desired zone and during the selection
zone's dot is blinking, the zone will be
able to be timed. Its icon
be illuminated with higher intensity.
For that:
1 Touch sensor
(8). The timer
indicator (5) of the selected plate
will show flashing "00". The light
ring of the knob will change to blue
color. If no action is performed on
the knob and no time is set, after
a few seconds, the timer will be
switched off.
2 Immediately after, turn the knob (2)
rightwards and select a cooking
time value between 1 and 99
minutes. If the first turn, from "00", is
done leftwards, the initial time value
will be 60 minutes. In both cases the
knob (2) has to be turned leftwards
to return the time to 00. Anytime the
time value is set to "00", if you turn
left the knob (2) the initial time value
will be 60 minutes.
3 When the timer indicator (5) stops
flashing, it will start counting down
the time automatically. When the
remaining time is 1 minute, the
countdown will be in seconds.
(8) will