Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
zones will light up and the value "0" will
be shown on its power indicator (3).
The clock timer indicator (12) will show
six segments indicating the flexible
zone selected. The power display
(3) for the other connected zones will
display three segments (see fig. 9).
You will have a few seconds to perform
the next operation; otherwise the
function will be disabled automatically.
You can assign the power by touching
the activated slider cursor (2). Once
the power has been selected, the led
(8) on the icon
(15).
To disable this function, you should
touch the slider cursor (2) in the
position "0".
Slide Cooking Function
(depending on the model)
This function allows to divide the
flexible zone into three areas (see
fig.15) and activates a predefined
power configuration. It will allow slide
the vessel from one area to another,
to cook with the power assigned to
each zone.
To activate this function, press the
sensor
(27). When doing
so, the led (28) located above said
icon and the decimal point (4) of
one of the linked zones turn on, also
showing the value "5" on its power
indicator (3), which corresponds to
zone # 2 . The power indicator (3)
of the other linked zone will show
three segments (see fig. 15 and 16).
You have a few seconds to place
the vessel in this area, otherwise the
function is automatically deactivated.
Once the vessel is placed, the power
level will appear automatically in the
power indicators (3): for zone #1,
the power level is 3, for zone #2 the
power level is 5 and for zone #3 the
power level is 9 (see fig.10).
To deactivate this function, you must
touch the "slider" cursor (2) in the
position "0".
40
Fig.15
Safety switch off function
If due to an error one or several
heating zones do not switch off, the
appliance will be automatically discon-
nected after a set amount of time (see
table 2).
Table 2
Selected
MAXIMUN
power
OPERATING TIME
level
(in hours)
0
1
2
3
4
5
6
7
8
1,5
9
1,5
10 minutes,
P
readjusts to level 9
When the "safety switch off" function
has been triggered, a 0is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Warning
Keep the control panel of the
heating areas clean and dry at all
times.
In the event of operating pro-
blems or incidents not mentioned
in this manual, disconnect the
appliance and contact the TEKA
technical service.
Suggestions and
recommendations
* Use pots or pans with thick, comple-
tely flat bottoms.
* Do not slide pots and pans over the
glass because they could scratch it.
* Although the glass can take knocks
from large pots and pans without
sharp edges, try not to knock it.
* To avoid damaging the ceramic
glass surface, do not drag pots
and pans over the glass and keep
the undersides of them clean and
in good condition.
* Recommended diameters of the pot
bottom (see ''Technical Data Sheet''
supplied with the product).
Try not to spill sugar or pro-
ducts containing sugar on the glass
as while the surface is hot these
could damage it.
0
Cleaning and maintenance
8
5
To keep the appliance in good
5
condition, clean it using suitable
4
products and implements once it has
3
cooled down. This will make the job
easier and avoid the build-up of dirt.
3
Never use harsh cleaning products or
2
tools that could scratch the surface, or
steam-operated equipment.
Light dirt not stuck to the surface can
be cleaned using a damp cloth and a
gentle detergent or warm soapy water.
However, for deeper stains or grease
use a special cleaner for ceramic hot
plates and follow the instructions on
the bottle. Dirt that is firmly stuck due
to being burned repeatedly can be
removed using a scraper with a blade.
Slight tinges of colour are caused by
pots and pans with dry grease residue
underneath or due to grease between
the glass and the pot during cooking.
These can be removed using a nickel
scourer with water or a special cleaner
Werbung
Inhaltsverzeichnis
