Technical Data; Engine Information; Description Of The Basic Machine Parts; Machine Control Elements - Vari Adela Pro Bdr-720D Bersetzung Der Originalbetriebsanleitung

2.3.1.1 T D
ECHNICAL
Description
Length x width x height
40
Weight
The machine's maximum working width
Safe slope operation
Cutting disk speed
41
Blade peripheral speed
Travel speed
Machine's surface power
42
Gear oil / specifications
Table 17: Technical specifications
2.3.1.2 E I
NGINE NFORMATION

Further information about the engine not stated here is available at the engine manufacturer's website
Description
Engine
Maximum (set) engine speed
Maximum (permanent) tilting of the engine
Maximum (short term ) tilting of the engine
44
Fuel tank capacity
Fuel
Engine oil filling
Oil grade
Table 18: Engine Technical Information
2.3.2 D
ESCRIPTION OF THE BASIC MACHINE PARTS
1 Cutting disc cover 7
2 Mudguard between 8
the wheels
3 Cutting disk 9
4 Blade (4 pcs) 10
5 Front handle 11
6 Handlebars holder 12
Table 19: Legend for Fig. 1
2.3.3 M C
ACHINE ONTROL
2.3.3.1 H
ANDLEBARS
•
The handlebars joint enables their height adjustment Fig. 2
Fig. 2 F
Fig. 2
B VERTICAL HANDLEBARS ADJUSTMENT :

Always switch off the engine before adjusting any handlebars position! There is the risk of losing control of your
machine!
•
For choosing a comfortable grip on the handlebars.
•
Fig. 2
A Loosen and completely unscrew the plastic thumbscrew
•
Adjust the height of the handle on the ground, so you can hold the handlebars comfortably.
•
Insert the plastic thumbscrew into one of the three holes in the foot of the handle joint – Fig. 2
40 Handlebars in the middle position for the handle height adjustment, control levers in the off position.
Actual speed of unloaded disc without any belt drive loss.
41
42 The machine's surface power depends on the type of mowed vegetation, the stated values are only theoretical, the machine's maximum working width is used for the calculation.
43 For more information about the engine, including the spare part numbers, visit www.honda-engines-eu.com.
44 Short term - up to one minute.
45 Measured per new standard Society of Automotive Engineers (SAE) J1349.
With regard to the ever increasing ratio of BIO-components in fuel, use fuel stabilizer.
46
26
ATA
Unit
mm
kg
cm

min -1
m.s -1
km.h -1
m 2 .h -1
l (litre) / SAE / API
Unit
min
l (litre)
petrol (unleaded)
l (litre)
SAE / API
Handlebars adjustment joint
Wing bolt for handlebars height adjustment
Wing nut for handlebars horizontal adjustment
Cutting disc drive clutch lever
Travel clutch lever
Service and parking brake lever
E
LEMENTS
H H
EIGHT AND ORIZONTAL
1,88 - 2,76 - 3,29 - 4,57 / R: 2,58 km/h
1380 – 1933 - 2300 – 3197 / R: n/a
0,5 / mineral gear oil 85W-90 / API GL-5
-
-1


46
13 Accelerator lever
14 Shift lever
15 Left wheel
16 Right wheel
17 Tank cap
18 Air filter
A
DJUSTMENT
B , horizontal adjustment Fig. 2
on the joint on the right.
1
BDR-720D Adela PRO
Value
1735 x 715 x 1490
86
70
10°
1480
54,3
.
43
Value
HONDA GCV200
3000 ± 100
20°
30°
0,91
45
Oct. No. 91-95
0,4
SAE 10W-30 / SJ nebo SH
19 Oil dipstick
20 Starter handle
21 Sulka hinge
22 Safety cover of the cutting disc
C and tilting to the transport position
D - and tighten it firmly.