Before Starting The Equipment; Construction - Scheppach HS81S Original Bedienungsanleitung

Cutting height max. 45°
height adjustment
saw blade swivel
suction port
weight
Noise values
The total noise values determined in accordance
with IEC 62841.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.

7. Before starting the equipment

• The equipment must be set up where it can stand
securely.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
identical to the mains data.
• Connect the machine to a properly installed pro-
tective contact socket, with at least 16A circuit
breaker.

8. Construction

Important. Pull out the power plug before carry-
ing out any maintenance, resetting or assembly
work on the circular saw!
Place all parts supplied on a flat surface. Grouping
equal parts.
Note: If compounds with a bolt (round head / or hexa-
gon), hex nuts and washers are backed up, the wash-
er must be fitted under the nut.
Insert screws each from outside to inside. Secure
connections with nuts on the inside.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
45 mm
Note: Tighten the nuts and bolts during assembly
only to the extent that they can not fall down.
0 - 70 mm
If you tighten the nuts and bolts prior to final assem-
0 - 45°
bly, final assembly can not be performed.
ø 40 mm
14 kg
Mounting the bench extension (fig. 3)
1. Turn the saw and place it on the floor with the
2. Align the bench extension (8) flush with the saw
3. Push table extension (8) onto the sawing table (1)
99.6 dB(A)
3 dB
4. Screw the support struts (16) to the table exten-
112.6 dB(A)
3 dB
5. Subsequently, tighten all screws.
Mounting rack (fig. 4-7)
1. Screw the four support legs (9) together with
2. Now place the rubber feet (17) onto the support
3. Now, screw the long centre brace (22) and the
4. Using two hex bolts (20) on each, loosely secure
5. Then, tighten all the nuts and bolts of the under-
Setting / mounting the riving knife (figs. 8-10)
m The setting Caution! Pull out the main plug!
The setting of the riving knife (6) must be checked
prior to commissioning of the riving knife (6)
must be checked prior to commissioning.
1. Set the saw blade (3) to the max. cutting depth,
2. Unfasten the bolt (23) from the bench insert (2)
3. The distance between the saw blade (3) and the
4. Loosen the mounting bolt (24) in order to pull out
5. Tighten the mounting screw (24) again and mount
bench facing down.
bench (1).
using the hex bolts (20) and loosely fasten the hex
nuts (19). Repeat for the opposite side.
sions (8) with the hex bolts (20) and the hex nuts
(19)
the support struts (16) onto the saw with the hex
bolts (20) (fig. 4). For this use the saw blade key
(15a/15b), part of the delivery contents (fig. 4).
legs (9) (fig. 5).
short centre brace (21) onto the legs (9) using the
hexagon head bolts (20) and the hexagon head
nuts (19). Make sure that the same braces face
each other. The long centre braces (22) must
be mounted parallel to the operator's side of
the saw. (Fig. 6).
the and hex nuts (19) at the drill holes of the rear
support legs of the support frame (18) (fig. 7).
Attention!
Both support frames must be fastened to the
back of the machine!
frame.
bring it to the 0° position and lock it.
using a Phillips screwdriver, and remove bench
insert (22) (fig. 8).
riving knife (6) must be max. 5 mm. (Fig. 9)
the splitting wedge (6) until the right distance is
adjusted (fig. 10).
the bench insert (2).
GB | 31