Safety Instructions - Sauter OFL3.0 Betriebsanleitung

6. Safety Instructions

General safety notices for
mounting equipment
! !
WARNING WARNING
Read the safety notices and
instructions provided with the
mounting equipment and the
electrical tool. Failure to comply
with safety notices and instruc-
tions may cause electric shock,
fire and/or severe injuries.
Keep all safety notices and
instructions safe for future
reference.
1. Disconnect the plug
from the mains socket and/or
remove the battery before con-
figuring device settings or repla-
cing accessories.
2. Correctly install the
router table including router lift
prior to installing the router mo-
tor. Correct assembly is import-
ant to prevent the risk of the
assembly collapsing.
3. Securely attach the
router motor on the router lift
prior to using it. If the electrical
tool is dislocated in the moun-
ting equipment, users may lose
control.
4. Position the
table on a secure, even, and
horizontal surface. If the router
table and/or router lift are dis-
located or are allowed to shake
this may cause severe injuries
during operation.
! ! WARNING WARNING
Safety at the workplace
1. Install the electrical
tool and accessories as specified
only. Use accessories specified
in the user manual only. The
tool or accessories must not be
modifi ed or used for any other
purpose than that intended. Do
not overload the electrically po-
wered tool.
Consider the working environ-
ment. Do not use the product in
environments subject to precipi-
tation or steam. Make sure the
environment is adequately lit.
Do not use electrically powered
tools in the vicinity of gas pipes
or flammable liquids. Maintain
a pleasant temperature in the
workshop so your hands are not
cold. Connect your electrically
powered tools to a leakage cur-
rent protection unit when wor-
king outdoors. Exclusively use
cables that have been approved
for outdoor use.
3. Keep
environment clean. An untidy
workshop or worktop may cau-
se injuries. Make sure there is
enough space to work safely.
4. Remove any poten-
tially available
or other metal parts from the
workpiece.
5. Check damaged parts.
Carefully check
device, cables, extension, plug
and accessories for signs of da-
mage. Check the alignment of
moving parts, connections, and
other circumstances that may
influence commissioning. Have
damage repaired by an authori-
sed specialist workshop before
commissioning the device or
accessories. Protect tools from
router
impact or falling down.
6. Use extraction equip-
ment. If there are extraction
ports provided, make sure that
they have been installed and
connected correctly.
7. Check all attachment
and lock screws, bolts, nuts,
and buttons on the electrically
powered tool, attachments and
router bits prior to commissio-
ning and make sure that they
have been securely closed and
tightened. Regularly repeat the
inspection if you rout for prolon-
ged periods of time.
! !
Electrical safety
1.
powered tools from the mains as
soon as you have stopped using
them, prior to all maintenance,
before each calibration, and pri-
or to replacing accessories, for
instance bit replacements. Make
sure the switch is set to "OFF".
Make sure the bit is no longer
rotating.
2.
if it is not possible to switch it on
or off. Have faulty switches re-
paired by a specialist workshop.
your working
3.
Do not carry the electrically po-
wered tool by the cable, do not
pull towards you using the cab-
le, and do not pull on the cab-
le the tool from keep the cable
nails, clamps away from heat, oil or sharp ed-
ges. Route the cable outside the
working area.
attachments,
! !
Personal safety
1.
sitors away. Do not allow child-
ren or visitors to touch the tool,
accessories
Keep
away from the working area.
Child-proof your workshop and
lock it.
2.
clothing. Do not wear widely cut
clothing or loosely hanging je-
wellery as this may get caught
in moving parts. We recommend
work gloves and anti-slip shoes
to work outdoors. Make sure
long hair is protected or cover-
ed.
3.
are not using in a dry and
locked place outside the reach
of children.
10
WARNING WARNING
Disconnect electrically
Do not use the device
Only use for purpose.
WARNING WARNING
Keep children and vi-
or attachments.
children and
Wear suitable
Keep any tools you
visitors
work