Removal From The Vehicle; Adjusting The Headrest - CYBEX SIRONA Z Bedienungsanleitung

1. Fold out the Load leg (3) until it locks into its foremost position. If you use
the Base Z, an acoustic warning signal will sound until the load leg has been
EN
correctly installed.
2. Release the ISOFIX-Release buttons (6) to extend the ISOFIX-Locking arms
(7).
The ISOFIX-Release buttons can both be released independently allowing the
��
ISOFIX-Locking arms to be adjusted independently.
3. Push the ISOFIX-Locking arms (7) out of the base to their furthest extent.
4. Place the base on an appropriate seat in the vehicle.
5. Push the ISOFIX-Locking arms (7) into the ISOFIX-Anchorage points (8) until
these lock into place with an audible "CLICK". The two ISOFIX-Indicators (9)
will switch from RED to GREEN.
6. Ensure the base is secure by trying to pull it out of the ISOFIX-Anchorage
points (8).
7. Push the Base (2) towards the backrest of the vehicle seat until it is fully
aligned with the backrest.
��
Moving the base from side to side will also brace it against the vehicle backrest.
8. Press the Load leg adjustment button (10) and extend the leg until it touches
the vehicle floor.
9. Pull the Load leg (3) out to the next locking position to ensure optimal force
transmission.
10. The Load leg indicator (11) switches to GREEN when the load leg is correctly
positioned on the vehicle floor. When using the Base Z, the acoustic warning
signal will also stop.
11. Place the car seat on the Base (2).
12. Please ensure that the car seat locks into place with an audible "CLICK".
13. Check whether the Seat locking indicator (12) on the base is GREEN.
14. In order to achieve the best possible protection, activate the Linear side-
impact protection (13) on the side of the car seat facing the vehicle door. To
do this, press the L.S.P Release button (14).
The car seat can also be used without the L.S.P. in use, if there is not enough
��
space in the vehicle.
8

REMOVAL FROM THE VEHICLE

1. To unlock the car seat from the base, push the Green seat release button (15)
and pull the Upper seat release button (16) up at the same time.
2. Tilt the seat slightly and lift it off the base.
3. Unlock the ISOFIX-Locking arms (7) on both sides by pressing the ISOFIX-
Release buttons (6) and at the same time pulling them back.
4. Pull out the Base (2) from the ISOFIX-Anchorage points (8).
5. Remove the Base (2) and slide the ISOFIX-Locking arms (7) completely back
into their transport positions.
6. Push the Load leg (3) back into its original position and then fold it in to save
space.
7. If you are using the Base Z, it is important to fully fold in the load leg so that
the acoustic warning is muted. There is a Load leg parking position (17)
indicated on the underside of the base to show you where the leg should go.

ADJUSTING THE HEADREST

The adjustable Headrest (18) can be adjusted by using the Headrest adjustment
handle (19) at the back of the Headrest (18). When adjusting the headrest ensure
that no more than 2 cm (approx. 2 finger's width) remain between the child's
shoulders and the headrest.
ROTATION FUNCTION
The rotation function is only available in combination with the Base Z. Pull the
Position adjustment handle (20) on the front of the seat and bring it into an upright
position. Now you can turn the seat.
��
We recommend to deactivate the L.S.P. before turnig the seat.
Before starting your journey, make sure that the seat is properly locked into place.
ADJUSTING THE LYING POSITION
To adjust the seat to the lying position, press the Position adjustment handle (20)
on the front of the car seat.
We recommend using the flattest lying position for children who are not yet able
��
to sit upright independently.
Always make sure that the car seat audibly clicks into place when adjusting it to
��
either the lying or sitting position.