Technical Data; Before Starting The Equipment - Scheppach HS80 Original Bedienungsanleitung

6. Technical data

AC motor ....................................... 220-240 V~ 50 Hz
Power consumption ........................... 1200 Watt (S1*)
.................................................... 1500 Watt (S6 25%)
Idle speed n ..............................................4800 min
0
Hard metal saw blade .............ø 210 x ø 30 x 2,6 mm
Number of teeth.......................................................24
Riving knife thickness .................................... 2.0 mm
Min. size of workpiece W x L x H ...... 10 x 50 x 1 mm
Table size ............................................ 485 x 445 mm
Table width extension ........................... 485 x 515 mm
Table size max. . ................................. 485 x 630 mm
Cutting height max. 45° ................................... 45 mm
Cutting height max. 90°................................... 48 mm
Tilting saw blade ......................................... 0-45° left
Suction connection ....................................... ø 35 mm
Weight ...................................................approx. 14 kg
Machine size (with extension)
W x L x H ....................................485 x 630 x 440 mm
*S1: Continuous operation at constant load
**S6 25% operating mode:
Continuous duty with intermittent loading (operating
time 10 min.)
In order avoid impermissible overheating of the mo-
tor, the motor should be driven for only 25% of the
operating time with the stipulated nominal power and
must then continue to run with no load for the remain-
ing 75% of the operating time.
Noise
The total noise values were determined in accord-
ance with EN 62841.
Sound pressure level L ............................87.5 dB(A)
pA
Uncertainty K .................................................... 3 dB
pA
Sound power level L ............................. 100.5 dB(A)
WA
Uncertainty K ................................................... 3 dB
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. To-
tal vibration values (vector sum - three directions) de-
termined in accordance with EN 62841.
NOTE: The specified device emissions values have
been measured in accordance with a standardised
test procedure and can be used for comparison of
one electric tool with another.
The specified device emissions values can also be
used for an initial estimation of the load.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
WARNING: The noise emission values can vary
from the specified values during the actual use of the
electric tool, depending on the type and the manner
in which the electric tool is used, and in particular
the type of workpiece being processed. Implement
measures to protect against noise nuisance. In doing
-1
so, take into account the complete working process,
including the times when the electric tool is working
without load or switched off.
Suitable measures include regular maintenance and
care of the electric tool and the insertion tools, regu-
lar breaks as well as proper planning of the working
process.

7. Before starting the equipment

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
m WARNING
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
• The equipment must be securely installed, i.e. bolt-
ed down on a workbench, base frame or similar.
Use the holes on the inner side of the frame legs
for this.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the On/Off switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
identical to the mains data.
• Connect the equipment to a properly installed pro-
tective contact socket, with at least 16 A circuit
breaker.
GB | 31