Technical Data - Scheppach HC110DC Originalanleitung

16 Important!
– For your own safety you must only use the ac-
cessories and additional units listed in the oper-
ating instructions or recommended or specified
by the manufacturer. The use of mounted tools
or accessories other than those recommended
in the operating instructions or catalogue may
place your personal safety at risk.
17 Noise
– Wear ear muffs when you use the compressor.
18 Replacing the power cable
– To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac-
turer or a qualified electrician. There is a risk of
electric shock!
19 Inflating tires
– Directly after inflating tires, check the pressure
with a suitable pressure gauge, for example at
your filling station.
20 Roadworthy compressors for building site opera-
tions
– Make sure that all lines and fittings are suitable
for the maximum permissible operating pressure
of the compressor.
21 Place of installation
– Set up the compressor on an even surface.
22 Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions. In
order to prevent the risk of serious or deadly injuries, we
recommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the electric tool.
ADDITIONAL SAFETY INSTRUCTIONS
Safety instructions for working with compressed
air and blasting guns
• The compressor pump and lines can become very hot
during operation. Touching these parts will burn you.
• The air which is sucked in by the compressor must be
kept free of impurities that could cause fires or explo-
sions in the compressor pump.
• When releasing the hose coupling, hold the hose cou-
pling piece with your hand. This way, you can protect
yourself against injury from the rebounding hose.
• Wear safety goggles when working with the blow-out
pistol. Foreign bodies or blown off parts can easily
cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of injury!
Safety information for paint spraying
• Do not process any paints or solvents with a flash
point below 55° C. There is a risk of explosion!
• Do not heat up paints or solvents. There is a risk of
explosion!
• If hazardous liquids are processed, wear protective
filter units (face guards). Also, adhere to the safety
information provided by the manufacturers of such
liquids.
• The details and designations of the Ordinance on
Hazardous Substances, which are displayed on the
outer packaging of the processed material, must be
observed.
• Additional protective measures are to be undertak-
en if necessary, particularly the wearing of suitable
clothing and masks.
• Do not smoke during the spraying process and/or in
the work area. There is a risk of explosion! Paint va-
pors are easily combustible.
• Never set up or operate the equipment in the vicin-
ity of a fire place, open lights or sparking machines.
• Do not store or eat food and drink in the work area.
Paint vapors are harmful to your health.
• The work area must exceed 30 m
tilation must be ensured during spraying and drying.
Do not spray against the wind. Always adhere to the
regulations of the local police authority when spray-
ing combustible or hazardous materials.
• Do not process media such as white spirit, butyl al-
cohol and methylene chloride with the PVC pressure
hose. These media will destroy the pressure hose.
Operating pressure vessels
• You must keep your pressure vessel in good work-
ing order, operate the vessel correctly, monitor the
vessel, carry out necessary maintenance and repair
work immediately and meet the relevant safety pre-
cautions.
• The supervisory authority may enforce essential con-
trol measures in individual cases.
• A pressure vessel is not allowed to be used if it has
faults or deficiencies that can endanger workers or
third parties.
• Check the pressure vessel for signs of rust and dam-
age each time before using. Do not use the compres-
sor with a damaged or rusty pressure vessel. If you
discover any damage, then please contact the cus-
tomer service workshop.
Do not lose these safety instructions

6. Technical data

Mains connection
Motor rating W
Operating mode
Compressor speed
Pressure vessel capacity (in liters)
Operating pressure
Theoretical intake capacity (l/min)
sound power level L
WA
uncertainty K
WA
and sufficient ven-
3
230 V ~ 50 Hz
2200
S1
2850 min
-1
100
approx. 10 bar
approx. 412
97 dB(A)
2.03 dB
GB 37