Cautions Regarding The Remote Control Unit; Connecting To An Antenna - Pioneer PDP-42RXE Benutzerhandbuch

Preparation

Cautions regarding the remote control unit

reparation
• Do not expose the remote control unit to shock, liquid, or
high humidity.
• Do not place the remote control unit under direct sunlight;
the unit may deform.
talling the Plasma Display
• The remote control unit may not work properly if the remote
sensor window of the Plasma Display is under direct sunlight
or strong lighting. In such case, change the angle of the
lighting or Plasma Display, or operate the remote control unit
closer to the remote sensor window.
• When any obstacle exists between the remote control unit
Over 50 cm
and the remote control sensor, the remote control unit may
not function.
• As the batteries become empty, the remote control unit can
function within a shorter distance from the remote control
sensor. Replace the batteries with new ones if necessary.
Over
• The Plasma Display emits very weak infrared rays from its
10 cm
screen. If you place such equipment operated through
infrared remote control as a VCR nearby, that equipment may
not receive commands from its remote control unit properly
or entirely. If this is the case, place that equipment at a
location far enough from the Plasma Display.
• Depending on the installation environment, infrared rays
from the Plasma Display may not allow this system to
properly receive commands from the remote control unit or
may shorten allowable distances between the remote control
unit and the remote control sensor. The strength of infrared
rays emitted from the screen differs, depending on images
displayed on the screen.
ating
oid direct sunlight. Maintain adequate ventilation.
cause the Plasma Display is heavy, be sure to have
meone help you when moving it.
ou place anything on the top of the Plasma Display it will not
eive enough ventilation and will not operate properly.
ow enough space around the upper and back parts when
talling to ensure ventilation around the backside.
rating Environment
ating environment temperature and humidity:
C – +40°C; less than 80 % RH (cooling vents not blocked)
ot install this unit in a poorly ventilated area, or in loca-
exposed to high humidity or direct sunlight (or storing
cial light)
Downloaded From TV-Manual.com Manuals
En

Connecting to an antenna

To enjoy a clearer picture, use an outdoor antenna. The follow-
ing is a brief explanation of the types of connections that are
used for a coaxial cable.
Preventing the Plasma Display from
falling over
Be sure to take special care to ensure that the Plasma
Display will not fall over.
Using a wall for stabilization
1
Attach the supplied falling prevention bolts (hooks) to the
Plasma Display.
2
Use storing cords or chains to stabilize the Plasma
Display appropriately and firmly to a wall, pillar, or other
sturdy element.
• Perform this work in the same way for both the left and
right sides.
ANT
• Use ropes, chains and fittings that are available on the
market.
• Connect the 75-ohm coaxial cable (commercially available) to
the ANT (Antenna) input terminal.
Antenna cable (commercially available)
If your outdoor antenna uses a 75-ohm coaxial cable with a
1 Hook
standard DIN45325 plug (IEC169-2), plug it into the antenna
terminal at the rear of the Plasma Display.
2 Cord or chain
Fitting
• A table or an area of the floor with adequate strength should
always be used to support the Plasma Display. Failure to do
so could result in personal injury and physical damage.
• When installing the Plasma Display, please take the neces-
sary safety measures to prevent it from falling or overturning
in case of emergencies, such as earthquakes, or of acci-
dents.
• If you do not take these precautions, the Plasma Display
could fall down and cause injury.
• The screws, hooks, chains and other fittings that you use to
secure the Plasma Display to prevent it from overturning will
vary according to the composition and thickness of the
surface to which it will be attached.
• Select the appropriate screws, hooks, chains and other
fittings after first inspecting the surface carefully to deter-
mine its thickness and composition and after consulting a
professional installer if necessary.
AV
AV 1 AV