Using On The Remote Control Unit - Pioneer PDP-42RXE Benutzerhandbuch

If you select "PIP" in step 5
You can select the position of picture in picture display.
Press the c or d button to move to PIP Position, then press
the \ or OK button.
PIP/TWIN
PIP/TWIN Mode
sing on the remote control unit
PIP/TWIN Input
erations
PIP Position
V channels SLEEP
Adjust
TV channels that you can watch under the
s, you cannot tune in those channels. For the
etting up TV channels" on page 25.
(Upper left)
he analogue channels
input mode analogue channels by pressing
n.
Stereo
h the input mode, the last channel you (Bottom left)
ted will be received.
ICAM
nnels
Bilingual
roadcasts
annel number, press the P + button on the
it. To decrease the channel number, press the
• You can select the positions by simply pressing the
– on the Plasma Display has the same
the remote control.
+/P – on the remote control unit.
8
Press the c or d button to select the required position
Monaural
etext information:
for the sub-picture, then press the [ or BACK button.
crease the page number.
9
Press the EXIT button.
crease the page number.
• You can turn off the sub-picture by simply pressing the EXIT
the remote control unit
button on the remote control.
Stereo
irectly by pressing buttons 0 to 9.
• Multiscreen function is available with the following combina-
tions:
ANALOG CH - AV1/2/3, S-VIDEO, VIDEO COMPONENT or HDMI
el 5 (1-digit channel), press 5.
el 25 (2-digit channel), press 2 then 5.
2
Teletext information:
Bilingual
roadcasts
3-digit page number from 100 to 899 directly
ns 0 to 9. See page 38.
ENTER button after entering the channel number,
Monaural
t channels quickly.
evious channel, press the CH RETURN button.
n each of the sound multiplex mode selected using the
Once the MONO mode is selected, the Plasma Display System sound remains mono even if the system receives a stereo broadcast. You must
witch the mode back to I or II mode if you want to hear stereo sound again.
electing a sound multiplex mode while the input source is AV1, AV2, AV3, S-VIDEO, VIDEO, COMPONENT or HDMI, does not change the type of
ound. In this case, sound is determined by the video source.
Downloaded From TV-Manual.com Manuals
PIP
AV1
FAVOURITE
CH
Return
(Upper right)
I
ATV
AAA
NICAM Stereo
(Bottom right)
ATV
BBB
NICAM
ATV
CCC
NICAM Mono
ATV
DDD
Stereo
ATV
EEE
DUAL
ATV
FFF
MONO
button, the display changes depending on broadcasting signals being received.
Each time you press , MTS toggles as shown below.
I
mode
INPUT
AV SELECTION SOUND EFFECT
1 1 2 2 3 3
Setting
4 4 5 5 6 6
II
7 7 8 8 9 9
0 0 CH
LIST
ENTER
1 ATV
AAA
NICAM Stereo
OK
CH
1 ATV
RETURN MENU
EXIT BACK
BBB
NICAM
P
button on
1 ATV
CCC
NICAM Mono
1 ATV
DDD
Stereo
1 ATV
EEE
DUAL
1 ATV
FFF
MONO
06
II
mode
MONO mode
MONO
1 ATV
AAA
MONO
1 ATV
BBB
MONO
1 ATV
CCC
MONO
1 ATV
DDD
MONO
1 ATV
EEE
MONO
1 ATV
FFF
MONO
1
1
1
1
1
1
En