Operation - Scheppach DP19Vario Original Bedienungsanleitung

4. Now place the drilling table holder (4) with the
rack (D) on the column (2) and guide the rack (D)
into the bottom rack guide on the column foot.
5. Use the ring (E) to secure the rack (D). Ensure
that the rack guide on the ring (E) is pointing
downwards. Tighten the integrated Allen screw to
affix the ring (E).
6. Place the hand crank (16) on the shaft of the drill-
ing table holder (4) and secure it with the Allen
screw. To do this, use the Allen key (B)
7. Screw one of the clamping handles (3) into the
drilling table holder (4).
Installing the machine head and column, Fig. 8
1. Place the machine head (13) on the column (2).
2. Align the drill's spindle with the table and the base
plate and tighten the Allen screw that is located on
the side of the machine head. (Allen key SW4 / A)
Installing the handles, Fig. 9+10
1. Screw three handles (10) tight in the handle brack-
et's thread. Use the hexagon spanner to do this.
2. Screw the remaining handle (6) into the handle
bracket for speed adjustment. Use the hexagon
spanner to do this.
Installing the folding swarf protector and the drill
chuck, Fig. 11
1. Push the folding swarf protector (11) onto the spin-
dle on the machine head and use a Phillips head
screwdriver to secure it.
Installing the chuck, Fig. 12
1. Clean the conical hole in the drill chuck and the
spindle cone with a clean piece of cloth. Make
sure that no dirt particles stick to the surface. The
slightest contamination on one of the surfaces
prevents the drill chuck from holding properly.
This may cause the drill to hit. If the tapered hole
in the drill chuck is extremely dirty, use a deter-
gent on a clean piece of cloth.
2. Push the drill chuck onto the spindle nose as far
as possible.
3. Turn the outer ring of the chuck counter-clockwise
(from the top view) and open the jaws of the chuck.
4. Place a piece of wood on the machine table and
lower the spindle down to the piece of wood.
Press firmly so that the feed fits strongly.
Insert/change battery: using the laser, Fig. 13
1. Insert/change battery: Switch off laser. Insert or
remove the battery compartment cover (14.1). Re-
move batteries and replace with new (2 AA bat-
teries).
2. To switch on: Move the ON/OFF switch (14) to
the "I" position to switch on the laser. Two laser
lines are projected on the workpiece and intersect
at the center of the drill tip contact point.
28 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
3. To switch off: Move the ON/OFF switch (14) to
the "0" position.
Installing the laser, Fig. 13
The laser can be adjusted using the adjusting screws
(F).
Important: All bare parts are greased in order to pro-
tect them from corrosion. Before mounting the drill
chuck (12) onto the spindle, both parts must be com-
pletely degreased using an environmentally friendly
solvent. This ensures optimal transmission of power.
Installing the machine
Before you use the drill for the first time it must be
mounted in a stationary position on a firm surface.
Use both mounting holes in the base plate to do this.
Ensure that the machine is freely accessible for op-
eration, adjustment and maintenance.
Important: The fixing screws may only be tightened
to a point where they do not distort or deform the
base plate. Excessive tension can lead to fracture.
Prior to starting
Ensure that the voltage of the mains supply complies
with the specifications on the rating plate. Connect
the machine only to a socket with the properly in-
stalled earthing contact. The table drill is equipped
with a no-volt trip that is designed to protect the
operator from an undesired restart following a drop
in voltage. Should this occur, the machine must be
manually restarted.

9. Operation

General (Fig.14)
To switch on the machine, push in the green On but-
ton "I" (9); the machine starts up. To switch off , press
the red Off button "O" (9); the device shuts down.
Ensure that you do not overload the device.
If the sound of the motor drops in pitch during opera-
tion, it is being overloaded.
Do not overload the device to the point where the mo-
tor comes to a standstill. Always stand in front of the
machine during operation.
Inserting the tool, Fig. 1
Make sure that the power plug is removed from the
socket-outlet before changing tools. Only cylindrical
tools with the stipulated maximum shaft diameter
may be clamped in the scroll chuck (12). Only use a
tool that is sharp and free of defects. Do not use tools
whose shaft is damaged or which are deformed or
flawed in any other way. Use only accessories and at-
tachments that are specified in the operating instruc-
tions or have been approved by the manufacturer. If
the pillar drill should become jammed, switch off the
machine and return the drill to its starting position.