Operation - Scheppach DP16VLS Originalbetriebsanleitung

Vibration emission value ah = 1,6 m/s
K uncertainty = 1,5 m/s
2
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Assembly
Column and machine foot, Fig. 3
Set the machine foot (1) down on the ground or the
1.
workbench.
Place the column (2) on the base plate so that the
2.
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the hexagonal screws (A) to fasten the col-
umn into the base plate and tighten them using a
hexagon spanner.
Table and pillar, Fig. 4
1. Slide the drilling table (3) onto the pillar (2). Position
the table directly above the base plate.
2. Install the table bolting (E) in the table unit from the
left side and tighten it.
Machine head and pillar, Fig. 5
1. Place the machine head (4) onto the pillar (2).
2. Put the spindle of the drilling machine with the table
and the base plate in the cover and fasten the 2
Allen screws (F).
Drill chuck protection with depth stop, Fig. 6
Fit the chuck protection with depth stop (8) onto the
spindle pipe and tighten the slotted screw (H).
Caution! The depth stop must be fed through the drill-
ing (I) on the housing. Screw on the two nuts (J1/2)
and place the indicator (K) onto the depth stop. The
indicator (K) must point at the scale.
Feed handles to the shaft hub, Fig. 7
Screw the feed handles (6) tightly into the threaded
holes in the hub.
Installing the chuck, Fig. 8
1. Clean the conical hole in the chuck (5) and the
spindle cone with a clean piece of fabric. Make sure
there are no foreign particles sticking to the surfac-
es. The slightest piece of dirt on any of these sur-
faces will prevent the chuck from seating properly.
This will cause the drill bit to wobble". If tapered
hole in the chuck is extremely dirty, use a cleaning
solvent on the clean cloth.
2. Push the chuck up on the spindle nose as far as it
wiII go.
3. Turn chuck sleeve anticlockwise (when viewed
from above) and open jaws in chuck completely.
24 І GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
All manuals and user guides at all-guides.com
2
4. Place a piece of wood on the machine table and
lower the spindle onto the piece of wood. Press
firmly to ensure that the food sits exactly.
Fastening radial drill press to supporting surface
For your own safety, it is highly recommended to in-
stall the machine on a bench or similar.
WARNING:
All the necessary adjustments for the good work-
ing of your drill press have been done at the factory
.Please do not modify them.
However, because of a normal wear and tear of your
tool, some readjustments might be necessary .
WARNING:
Always unplug our tool from power source before any
adjustment"
Adjusting the spindle retaining spring (Fig.9)
It may be necessary for the spindle retaining spring to
be adjusted because of changed tension, making the
spindle return too quickly or too slowly.
1. To provide more space, lower the table.
2. Work on the left side of the drill.
3. Put a screwdriver in the front lower notch (L), keep-
ing it in place.
4. Remove the outer locknut (O) with a flat spanner
(SW16).
5. Leaving the screwdriver in the notch, loosen the in-
ner locknut (N) until the cut-out is released from the
boss (P). WARNING! Spring is under tension!
6. Using the screwdriver, carefully turn the spring cap
(M) anti-clockwise until you can press the notch
into the boss (P).
7. Lower the spindle to the lowest position and hold
the spring cap (M) in place. When the spindle
moves up and down as desired, retighten the inner
locknut (N).
8. If it is too loose, repeat steps 3-5. If it is too tight,
repeat step 6 in reverse order.
9. Using a flat spanner, tighten the outer lock-
nut (O) against the
NOTE: Do not over-tighten and do not restrict the
movement of the spindle!

Operation

WARNING:
If you are not familiar with this kind of machine,
take advice from an
In any case you should have read and understood the
safety and operational instruction before attempting
to operate this product.
Pivoting the table, Fig. 10
1. To bring the table (3) to the inclined position, re-
lease the table locking (S) and adjust the desired
table angle. Re-tighten the table locking
inner locknut (N).
experimented person.