Before Starting The Equipment; Montage; Operation - Scheppach 5906810901 Original Bedienungsanleitung

7. Before starting the equipment

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!

8. Montage

Column and machine foot (Fig. 3)
1. Set the machine foot (1) down on the ground or
the workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the hexagonal screws (A) to fasten the col-
umn into the base plate and tighten them using a
hexagon spanner.
Table and pillar (Fig. 4)
1. Slide the drilling table (3) onto the pillar (2). Posi-
tion the table directly above the base plate.
2. Install the table bolting (E) in the table unit from
the left side and tighten it.
Machine head and pillar (Fig. 5)
1. Place the machine head (4) onto the pillar (2).
2. Put the spindle of the drilling machine with the ta-
ble and the base plate in the cover and fasten the
2 Allen screws (F).
Drill chuck protection with depth stop (Fig. 6)
1. Fit the chuck guard (7) on the spindle tube and
tighten the Philips screw (H).
2. Unfold the chuck guard (7).
3. Remove the nut (G) from the depth stop rod (8).
4. Guide the depth stop rod through the hole (I) on
the machine head (4)
5. Fasten the depth stop rod (8) with the nut (G) in
the hole of the chuck guard (7).
6. Turn the pointer on the depth stop rod (8) to the
scale on the machine head (4).
The nuts (J) act to limit the depth.
Feed handles to the shaft hub (Fig. 7)
1. Screw the feed handles (6) tightly into the thread-
ed holes in the hub.
Installing the chuck (Fig. 8)
1. Clean the conical hole in the chuck (5) and the
spindle cone with a clean piece of fabric. Make
sure there are no foreign particles sticking to the
surfaces. The slightest piece of dirt on any of
these surfaces will prevent the chuck from seating
properly. This will cause the drill bit to wobble". If
tapered hole in the chuck is extremely dirty, use a
cleaning solvent on the clean cloth.
2. Push the chuck up on the spindle nose as far as
it wiII go.
3. Turn chuck sleeve clockwise (when viewed from
above) and open jaws in chuck completely.
4. Place a piece of wood on the machine table and
lower the spindle onto the piece of wood. Press
firmly to ensure that the food sits exactly.
Installing laser module (Fig. 15, 16)
Fasten the laser module (13) with the countersunk
screw (U) onto the machine head (4) as shown in the
figures.
Make sure the plastic pin on the laser module sits in
the hole without thread.
Fastening radial drill press to supporting surface
For your own safety, screw connection on a work-
bench or similar is strongly recommended.
Warning:
All the necessary adjustments for the good working of
your drill press have been done at the factory. Please
do not modify them.
However, because of a normal wear and tear of your
tool, some readjustments might be necessary .

9. Operation

Warning:
If you are not familiar with this kind of machine, take
advice from an experimented person. In any case you
should have read and understood the safety and op-
erational instruction before attempting to operate this
product.
Pivoting the table (Fig. 10)
1. To bring the table (3) to the inclined position, re-
lease the table locking (S) and adjust the desired
table angle.
2. Re-tighten the table locking.
Adjusting table height (Fig. 11)
1. Loosen the table support lock handle (E).
2. Adjust the table (3) to the desired height.
3. Re-tighten the table locking (E).
4. Note: It is better to lock the table to the column in
a position so that the tip of the drill bit is just slight-
ly above the top of the workpiece.
www.scheppach.com
GB | 25