Before Starting The Equipment; Operation - Scheppach DH1300PLUS Original Bedienungsanleitung

The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.

6. Before starting the equipment

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Warning!
Always pull the power plug before making adjust-
ments to the equipment.
Check the drilling point for concealed electrical ca-
bles, gas and water pipes using a cable/pipe detector.
Additional handle (Fig. 2 – Item 8)
For safety reasons you must only use the ham-
mer drill with the additional handle.
The additional handle (8) enables you to achieve bet-
ter stability whilst using the hammer drill. The machine
must not be used without the additional handle (8) for
safety reasons. The additional handle (8) is secured
to the hammer drill by a clamp. Turning the handle
anticlockwise (looking from the handle) will release
the clamp. Turning the handle clockwise will tighten
the clamp. First release the additional handle clamp.
You can then swing the additional handle (8) into the
most comfortable working position for you. Now turn
the additional handle in the opposite direction again
until the additional handle is secure.
Depth stop (Fig. 3 – Item 9)
The depth stop (9) is held in place with the locking
screw (A) on the additional handle (8) by means of
a clamp.
• Undo the locking screw (A) and fit the depth stop
(9).
• Set the depth stop (9) to the same level as the drill
bit.
• Pull the depth stop (9) back by the required drilling
depth.
• Retighten the locking screw (A).
• Now drill the hole until the depth stop (9) touches
the workpiece.
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Tool insertion (Fig. 4)
• Clean the tool before insertion and apply a thin
coating of drill bit grease to the shaft of the tool.
• Pull back and hold the locking sleeve (2).
• Insert the dust-free tool into the tool mounting as far
as it will go whilst turning it. The tool will lock itself.
• Check that it is properly secure by pulling the tool.
Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and remove
the tool.
Dust collection device (Fig. 6)
Slide the dust collection device (B) over the drill bit
before carrying out any hammer drilling vertically
above your head.

7. Operation

Danger
To prevent all danger, the machine must only be
held using the two handles (5/8). Otherwise there
may be a risk of suffering an electric shock if you drill
into cables.
Status indicator (Fig. 1)
The status indicator (6) lights up when the power plug
is connected.
Switching On and Off (Fig. 1)
To switch on: Press and hold the operating switch (4).
To switch off : Let go of the operating switch (4)
Button hammer drilling / chiselling (Fig. 7)
• To drill, press the button (D) on the rotary switch (3)
and at the same time turn the rotary switch (3) to
switch position C.
• For hammer drilling, press the button (D) on the ro-
tary switch (3) and simultaneously turn the rotary
switch (3) to position E.
• For chiseling, press the button (D) on the rotary
switch (3) and simultaneously turn the rotary switch
(3) to position F. In switch position F the chisel is
not locked.
• For chiseling, press the button (D) on the rotary
switch (3) and simultaneously turn the rotary switch
(3) to position G. The chisel is locked in position G.
Notice!
Only low pressure is required for hammer drilling.
Excessive pressure will exert an unnecessary force
on the motor. Check the drill bits at regular intervals.
Sharpen or replace blunt drill bits.