Honda HF2317 Übersetzung Der Originalbetriebsanleitung, Gebrauchsanleitung Seite 10

4.10.b USB ACCESSORY HOLDER
HF2417HM• HF2417HT•
Support to hold the USB accessory
4.11 GRASS CATCHER TIPPING CONTROL
HF2•••HB• HF2•••HM•
The grass catcher may be tipped to
empty by pulling the lever (4.11.1), which
can be extracted from its housing.
HF2•••HT•
To empty the grass catcher, press the but-
ton (4.11.2) and hold it down until the bag
reaches its highest position. (
The grass catcher returns to the working po-
sition by pressing the button (4.11.3), keep-
ing it pressed until the pawl hooks into place
and the control motor stops.
4.12 "MULCHING" ENGAGE LEVER
HF2417HM• HF2417HT•
"Mulching"is engaged with the lever.
«A» = function engaged
«B»= function disengaged
– Only move the gear shift when the cutting means is disengaged.
– With the "mulching" function engaged, the exit guards must
always be fitted (grass catcher or discharge guard) (
4.13 INDICATOR LIGHTS AND AUDIBLE WARNING DEVICE
ON THE CONTROL PANEL
HF2317•••
i.1
o c d e
EN 10
HF2625H♦•
4.2
4.3
4.9
5.4.6).
4.4
HF2625H♦•
A
f g h i j
HF2417HB•/HM•
k
i.1 o
4.7
HF2417HT•
B
k
4.1
A
i.1 o
When the key (4.4) is turned in the «ON» position, all the lamps light
on at the same time for about one second (with a brief sound warn-
ing) to indicate that the machine is working properly.
The display (a) enters into " information " mode and by using the
MODE (b) button it is possible to select the following functions:
– a.1)
B
HF2625•••
4.12
– a.2)
4.6
– a.3)
5.3.5).
Briefly press the MODE button and release it to turn the
icons a.1, a.2, a.3 on in sequence. The alphanumeric digits
on the display show the data associated with the selected
icon, the last digit is reserved for the unit of measurement.
Do not use
RPM
Afterwards, when a lamp comes on, it indicates:
c) the operator is absent;
d) grass catcher missing;
– If it flashes, it means that the grass catcher is full and
needs to be emptied.
e) parking brake engaged;
f) Battery not fully recharged: Seek out the causes in chapter
7 of this manual;
– If it is blinking, it means that the battery is reaching the
over-voltage threshold; stop the machine immediately,
disconnect the battery and contact an authorised ser-
vice centre.
g) cutting means engaged;
HF2625HM•
n
a
a.1 a.2 a.3
d c e f
g
4.11.2
HF2625HT•
n
B
a
4.8
4.11.3
a.1 a.2 a.3
d c e f
g
4.10.a
4.11.1
Hour counter: Alphanumeric digits show the hours
driven, divided into hours and tenths of hours.
The unit of measurement is followed by the letter h;
A
4.5
RPM counter: indicates the engine rotational
speed by numerical values.
Displayed value:
< 1600 min engine at minimum speed
-1
> 2600 min travelling speed, cutting speed
-1
Voltmeter: The alphanumeric digits show the bat-
tery voltage.
counter value to set engine speed.
l
j
i
h b
m
l
j
i
A
h b
m
B