Herunterladen Inhalt Inhalt Diese Seite drucken

Novoferm iso45-4 Serie Montage-, Bedienungs- Und Wartungsanleitung Seite 9

Vorschau ausblenden Andere Handbücher für iso45-4 Serie:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 3
GB
Instructions for installing sectional garage doors
Types iso45-4, with (front mounted [VL] or rear
mounted [HL]) torsion spring
Incorrect installation renders the door manufacturer's
liability null and void.
– Installation only by suitably qualified installers in
accordance with the requirements of EN 12604 and EN
12453 –
Please read these instructions carefully prior to installation.
Intended use of garage doors
Garage doors are intended for installation in areas
accessed by people in privately used garages and they
are used to enable safe approach of consignments and
vehicles, accompanied or driven by people, in
residential areas.
Although garage doors are tested to national and
international stands and manufactured in accordance with
best engineering practice, they can pose hazards.
Use of the doors is classified as improper particularly in the
following cases:
Their use does not conform to the intended use
Failure to observe the minimum protection specified in
EN 12453 during utilization
Improper maintenance or servicing, particularly by
unauthorized individuals
Application of loads exceeding normal manual
pressure on the door leaf (never apply loads to door
leaf when opening and closing; never intentionally try
to hinder opening and closing)
Use of inappropriate or incorrectly configured operators
Installation or attachment of improper components and
parts in or to the door, the locking system or the
operator and/or modification of their original as-
delivered status
Changes to or modifications of the door or its
components
Failure to observe the assembly, operating and
maintenance instructions, respective country-specific
standards and guidelines as well as applicable safety
regulations
The door is not in safe working order
Door elements, operators and remote controls are not
children's toys
The door element is not suitable for use by people
(including children) with limited mental, physical or sensory
capacities or a lack of experience or knowledge. However,
the door can be used in areas where it is within reach of
children.
A door element is not suitable for use as a load-bearing
component. The door must be installed vertically or
horizontally in keeping with its design. Accordingly, the
tracks must be perpendicular or aligned as specified in the
installation instructions.
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage
Scope of delivery:
Pallet containing door leaf sections with torsion spring
assembly and box containing individual parts
Frame packet
Before commencing installation, make sure you have
the following tools to hand (unless you have other means of
access, place them in the garage before installing the
garage door):
Folding ruler/measuring tape, spirit level, plumber's wrench,
reversible ratchet with extension and SW 7, 10 and 13
spanners (possibly open-end or socket wrench, as well),
Phillips screwdriver sizes 2 and 3, slot screwdriver, hammer
drill with appropriate 10mm drill bit (depth: min. 65mm), at
least 2 screw clamps, possibly ladders, chalk, cutter, wire
cutter or power cutter, metal saw, small pair of pliers,
squared timber, hammer and chisel.
Suitable fastening material for the structural conditions.
Caution: Prior to use, please make sure the S8 wood
screws and S9 plugs included in the delivery are
suitable for the structural conditions. Only install in
areas that are strong enough to support the load.
Caution!
When using fastening materials not included in the scope
of supply, always make sure that the type and number (e.g.
wall anchors, screws, plugs, etc.) have the capacity to bear
at least the same loads as the supplied fastening materials.
Important:
The garage door may only be mounted in the finished
opening and on the finished floor!
To be on the safe side, please compare the dimensions of
the garage with the coordinating size of the garage door
prior to commencing installation.
Minimum inside width of garage
= Coordinating width + 160mm
Minimum height of garage ceiling
= Coordinating height + 215 mm for VL
= Coordinating height + 115 mm for HL
Minimum rebate width left and right = 35 mm
All information relating to left or right assembly applies
from the inside of the garage looking out! All
dimensions
in
alterations.
Text sections in:
normal font
italic font
inverted font
Combinations of letters / numbers, e.g. S8, refer to the
corresponding fastening material in the illustrations
section, parts suffixed by a subscript L or R, such as 1
(look for marks on the parts) indicate that they are for
left or right use only, parts without subscript can be
used both left and right. Numbers in square brackets,
e. g. [5.10], refer to the corresponding illustrations in
the illustrations section.
door!
- 7 -
millimetres.
Subject
to
 apply to VL + HL
 apply to VL only
apply to HL only
technical
L

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis