Novoferm iso45-4 Serie Montage-, Bedienungs- Und Wartungsanleitung Seite 13

GB
( 27 ) Is the wound cable seated exactly in the drum guides? Are
there at least 2 turns of cable on the drum for safety
reasons?
( 28 ) Are the centre bearings aligned exactly to ensure smooth
shaft movement?
[
1.35
( 29 ) Rollers: Can all rollers be easily turned by hand when the
door is closed?
[
1.55 b
( 30 ) Has the top roller been correctly adjusted?
( 31 ) When the door is open, do all roller axes extend the same
distance out of their holders?
( 32 ) Doors with operators: Has the locking mechanism been
dismantled?
[ ]
1.50 db
Instructions for dismantling sectional garage
doors
Types iso45-4, with (front mounted [VL] or rear
mounted [HL]) torsion spring
- Dismantling by qualified installers only -
Please read these
disassembly.
The following tools are required for disassembly:
SW 7, 10 and 13 open-end or socket wrench, reversible ratchet
with extension and SW 7, 10 and 13 spanners, Phillips
screwdriver sizes 2 and 3, at least 2 screw clamps, possibly a
hammer and chisel.
( 33 ) Release tension on the torsion spring
Caution: Make sure you wear suitable personal
protective equipment and have secure footing when
releasing the springs!
Move the door leaf to closed end position. Insert the spring
tensioning tube into the holder. Hold the spring tensioning
tube and carefully loosen the spring clamping screws.
Release torsion spring 35
the opposite direction of the arrow. Springs are always
released from the top down.
( 34 ) Remove the steel cables and dismantle the torsion springs.
( 35 ) Guard the pairs of horizontal tracks against falling down.
( 36 ) Remove the 89°arcs.
( 37 ) Unscrew and remove the fastening of the pairs of horizontal
tracks from the ceiling and walls.
( 38 ) Fold the pairs of horizontal tracks and unscrew them from
the door frame.
( 39 ) Remove the anchor tracks.
( 40 ) Unscrew the pairs of horizontal tracks from the track
connector.
( 41 ) Section by section, working from the top down, dismantle
the rollers and hinges and remove each section from the
door.
( 42 ) Guard the door frame against falling over. Unscrew the
wall and floor fastenings, carry the door frame out of the
opening, place it on the ground and dismantle it (in reverse
order compared to installation).
Instructions for
sectional garage doors
Types iso45-4, with (front mounted [VL] or rear
mounted [HL]) torsion spring
Incorrect operation
manufacturer's liability null and void, as does failure to use
original spare parts or any unauthorized changes to the
structure of the door. This garage door is designed for
private use. If used commercially, compliance with
corresponding national and international regulations is
mandatory.
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage
.
] [ ]
2.15
]
instructions carefully
with both tensioning tubes in
R/L
operating and servicing
or maintenance renders
Operation:
The mechanical equipment of this door is designed to mitigate
to the greatest possible extent the risk of anyone operating or
standing near the door being crushed, cut, clipped or otherwise
injured. To ensure safe use of the door, the following points
must be observed:

Before and during the cycle make sure nobody and nothing
is within range of moving parts (e.g. door leaf, rollers, etc.),
except for the operator.

Manual operation of the sectional garage door is only
permissible using the outdoor or indoor handles, or the
hand pull. Operators must not interfere with moving parts.

Lock function

Turning the key fully enables the sectional garage door
to be opened and closed without a key at all times.

Turn the key 3/4 to open the door and back the other
way 3/4 to lock it when closed.

The inside unlocking/locking knob can be activated to
enable opening and closing without a key.

Keep people and objects out of opening range when
operating the sectional garage door from inside or out.
prior to

When opening the door leaf, make sure it is in end position
and has come to a standstill before taking any other action.
Sufficient spring tension must be present.
Caution: The spring tension may only be adjusted by a
qualified installer!

Operation of this door is only permissible at temperatures
between -20°C and +40°C.

The A-weighting sound pressure level is less than 70 dB.

Make sure the catch engages securely when closing the
sectional garage door.

When equipping this door with an operator

the system must comply with all applicable EU
Directives (Machinery, Low Voltage, EMC Directives,
etc.), as well as with all applicable national and
international norms and regulations

the system must be duly fitted with a type plate and CE
mark by the manufacturer, and a declaration of
performance must have been issued

handover literature must be available in the local
language and must be kept in a safe place throughout
the service life of the garage door

the lock (catch, staple plate) must be dismantled.
Removal of the hand pull is absolutely essential!!
Adjustments to the garage door operator may only be
performed by appropriately qualified installers!
Maintenance:
The following must be checked following installation of the
garage door and every 6 months thereafter, at least.
Maintenance by unskilled or suitably qualified installers:

Grease the roller axes in the holders and clean the pairs of
horizontal tracks once installation of the sectional garage
door is complete and at intervals of approx. 5,000 cycles.

Do not grease the lock cylinder; if it does not run smoothly
enough, treat it with graphite spray.

Ensure sufficient ventilation (drying) of the door frame;
water drainage must also be ensured.
the 
Keep all corrosives or other aggressive agents such as
acids, lyes, salts, etc. away from the sectional garage door.
Only use mild household detergent to clean the door.

Steel-filled sectional garage doors are coated with polyester
at the factory. Any paintwork on site must be applied within
door!
- 11 -