Inhaltsverzeichnis - Novoferm iso45-4 Serie Montage-, Bedienungs- Und Wartungsanleitung

GB
( 13b ) Ceiling fastening: Anchor track 27 + connecting
bracket 28 + S6 + S12 + 2x each S8 + S9
. Diagonal reinforcement can be added to
[ ]
2.15b
enhance stability.
Fasten track mounting bracket 19 to the ceiling, together
with the anchor tracks 27 + connecting bracket 28 + S6 +
S12 + 2x each S8 + S9
ceiling brackets at the front on pair of tracks 14
and track connector 6 if BRB is 3530mm or more and
BRH 2126mm or more. Anchor tracks 27 + connecting
bracket 28 + clip plate 29 + S6 + S12 + 2x each S8 +
S9)
[ ]
1.30 f
Assembling the torsion spring
( 14 ) Insert pre-assembled right torsion spring 35
plate 4 and fasten with S11
R
bearing 37 (S8 + S9).
Insert 2x S5 screws through clip plate 29 and into track
connector 6. Pre-assemble centre bearing 37 and base
plate 103 using S6 + S12 and use S12 to bolt to clip plates
29 . Insert pre-assembled right torsion spring 35
[ ]
2.15 da, db
into HL sole plate 21
Attach ceiling mount to centre bearing 37 (anchor tracks 27
+ connecting bracket 28 + S6 + S12 + S8 + S9)
Mount 1 centre bearing 37
BRB 3529mm (a>120mm).
Mount 2 centre bearing
BRB 3530mm or more. Same procedure with 2nd bearing
on left spring. Make sure centre bearings are exactly
aligned to ensure smooth operation. Plug coupling 38
onto shaft end and assemble left torsion spring 35
the same procedure as for right torsion spring 35
coupling 38 to the centre over the shaft ends and tighten
gently by hand. [
1.35 c
Assembling the door leaf
( 15 ) Bottom section 44 (B)
( 15a ) Slide floor seal 47 into floor track and insert rubber
end plugs 45
protective foil around an end cap and remove [
]. Bolt floor handle 49 using S10 to bottom section
bb
.
[ ]
1.40 d
( 15b ) Bolt one external hinge 48
the bottom section 44 using S10
( 15c ) Attach logo [
1.40 e
( 15d ) Before inserting bottom section 44, use a damp cloth
to clean angular frames 1
section 44 between angular frames 1
safeguard against falling over. Push rollers 56 into
roller holder 61, position in vertical track and bolt to
external hinges 48
( 15e ) Unroll cable 104 from torsion spring 35
guide behind external hinges 48
( 15f ) Unroll cable 104 from HL torsion spring 35
remove as no longer needed [2.15 i]. Screw on
protective cover for drum 106 using S10 [2.15 k].
Guide cable 104 (longer version; you will find it in the
frame box for the HL version) through deflection
pulley bracket 101
for HL torsion spring 35
[2.20 b], guide it down behind external hinges
48 /48 [2.20 a], attach to bottom cable mount
R L
57 /57 [1.45 c]. Pull cable 104 from behind through
R L
groove on the drum and tension [2.20 b]. From the
drum, measure 1 metre of cable 104 and use suitable
cutting tools (wire cutter, power cutter) to shorten the
excess [2.20 d]. Pull cable back, lock in place in
drum with grub screw and rewind on drum [2.15 k].
( 15g ) Push rollers 56 into roller holder 61 use S5 + S12 to
bolt to bottom cable mounts 57
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage
.
[ ] [ ]
1.30 d ; 2.15 c
. Caution: Mount additional
[ ]
1.30 e
[ ] [ ]
1.35 ; 2.15
. Mount centre
[ ]
1.35 aa, ab
[ ]
1.35 b, da, db ;
/21 and fasten with S11
R L
[
on garage doors widths up to
37
s on garage doors widths or
.
] [ ]
; 2.15 h
[ ] [ ] [ ] [
1.40 ; 1.45 ; 1.50 ; 1.55
/45 . Carefully cut open the
[ ]
1.40 a
R L
/48 each left and right to
R L
.
[ ]
1.40 c
].
/1 . Position bottom
[ ]
1.30
R L
/48 using S5 + S12 [
1.45 a, aa
R L
/48
[
1.45 b
R L
/101 [2.15 j], pull it to the drum
R L
/35 and clamp in place
R L
/57 . Position cable
R L
[ ]
1.30 c ;
( 16 ) Lock section 67 (S)
( 16a ) Insert lock section 67 into angular frames 1
/14
R L
( 16b ) Assemble the lock set on the lock section as shown
in sole
R
R
.
[ ]
2.15 e, f
.
]
2.15 g
Garage doors without operators
( 16c ) Bolt catch 79 to lock section using S10
( 16d ) Hold bolt bar 80 to catch 79 and rotating arm and
( 16e ) Insert bolt bar 80 into rotating arm together with catch
using
L
. Slide
R
( 17 ) Middle section(s) 86 (M)
Using the same procedure as for the bottom and lock
sections, insert middle section(s) 86 into angular frames
] [ ]
1 /1
; 2.20 .
R L
68.
( 18 ) Top section 87 (K)
( 18a )
1.40 ba,
( 18b ) If installing NovoPort, the outer ring on top
/1 and
R L
].
/35 and
R L
].
( 18c )
/35 and
R L
( 19 ) Adjusting the rollers:
( 19a ) Manual and ceiling pull operation: Pull all rollers away
door!
- 9 -
with cable eye stiffener and plastic bushing 59 on the
bolt and secure with splint 60 [
assembled cable fasteners with rollers into vertical
track and bolt to bottom section using S10 [
safeguard against falling and bolt one each external
hinges 48 /48 using S10 left and right to the lock
R L
section 67, push rollers 56 into roller holder 61, insert
into vertical tracks and bolt to external hinges 48
using S5 + S12 . Bolt middle hinges 68 to floor
[ ]
1.50 a
and lock section using S10
in the exploded view
[
1.50 c
spacer frame on iso 34) + outdoor handle + indoor
handle (69-78). Insert lock plate with cover plate from
the outside into rectangular hole on lock section and
bolt from the inside using lock set. Push outdoor
handle through the holes in the lock (crank pointing
up) and bolt to indoor handle from the inside.
Caution: Rotating arm (die cast zinc) must point
upwards to the right!
shorten to correct length, if necessary, using metal
saw or power cutter
[ ]
1.50 da
79 and use S14 to fasten bolt bar 80 and catch
.
]
db
and fasten with S10 + S5 + S12 + 48
Bolt top roller block 90a/90b to top roller holder
88 using S5 + S12 [1.55 aa].
105 to top roller holder 88 using S5 + S12 [
R/L
roller 90a must be removed on the drive side.
Holding the top roller in your left hand, make 2
indents with a pair of pliers. Twist the roller to the
right to loosen and remove the outer ring [
If installing NovoPort, the outer ring on top roller 105
must be removed on the drive side. Grasp the top
roller with your left hand and insert a screwdriver
between the rib and tooth on the roller. Twist the roller
to the right to loosen and remove the outer ring.
].
cb
Insert top section 87 into angular frames 1
safeguard against falling over and bolt one each top
roller block 90 with top roller holder 88 left and
right to top section 87 using S10
section 87 into angular frames 1
against falling over and bolt one each top roller block
105 with top roller holder 88 left and right to top
R/L
section 87 using S10 [2.20 c].
hinges 68 using S10 to the top and middle sections
[ ].
1.50b
from the door leaf in the direction of the arrows until
the door leaf lies flush against the frame seal
(distance between section edges and grey part of the
]. Insert pre-
1.45 c
].
1.45 d, e
/1 ,
R L
/48
R L
.
[ ]
1.50 b
. Lock plate + lock set (+
]
.
[ ]
1.50 db
.
[
1.50
/48 + 56 + 61 +
R L
Bolt top roller block
].
2.20ca
]
.
1.55 ab
[
2.20
/1 ,
R L
.
[ ] Insert top
1.55ac
/1 , safeguard
R L
Bolt the side and middle