Novoferm iso45-4 Serie Montage-, Bedienungs- Und Wartungsanleitung Seite 10

GB
Pre-assembling the door frame
( 1 ) Lay wood or similar protective material (to guard against
scratches) under the angular frames 1
frame 1 + frame panel 3 + angular frame 1
R
(tapping screws are pre-assembled)
plate 4 /4 to the top corner using S11
R L
Note! If using a window as the top section, we recommend
taking the panel seal from frame panel 3 and turning it 180
degrees (see label on window).
( 2 ) Depending on rebate width and plug points, bolt wall anchor
7 to angular frames 1
R
( 2a ) Rebate wider than 120mm - Variant 1:
Wall anchor 7 facing outwards
( 2b ) Rebate 35 - 119mm wide Variant 2: Wall anchor 7
facing inwards
If using other fasteners, make sure their load
absorption capacity is at least equal to that of the
supplied wall anchors 7.
( 3 ) Garage doors without operators;
Spacing X less than or equal to 10mm [
Pre-assemble staple plate 93
BRH table on angular frame 1
[ ].
1.10e
Bolt securing bracket 94 to staple plate 93
S12 [ ] .
1.10e
Spacing X greater than 10mm
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage
[ ] [ ]
1.10 , 2.10
/1 . Bolt angular
R L
L
. Bolt VL sole
[ ]
1.10 a
.
[ ]
1.10 b
/1 using S6 + S12.
L
.
[ ]
1.10 ca
.
[ ]
1.10 cb
1.10 diagram
or 93 at height Y as per
R L
using S6 + S12. [
R/L
using S6 +
R/L
see
[1.65]
Installing the plugs for the door frame
( 4 ) Position the door frame behind the opening, safeguard
against falling over, use a spirit level to ensure exact
parallel and angular alignment. Clip panel holder 13 to
together
centre of panel 3. Scope of supply includes 2 panel holders
for BRB 3530mm or more. Fasten the entire angular frames
using S8 + S9
with bolt S8 + S9 and shim U1.
angular frames 1
process; if necessary, provide suitable underlay before
tightening the screws!!! VL: Minimum distance between
upper edge of frame and ceiling = 5mm!!!
Pre-assembling the pairs of horizontal tracks
( 5 ) Bolt right 14
corresponding moulded end piece 16
connecting plate 18 using (S6 + S12)
track mounting bracket 19
connecting angle 20
plate 21
].
Assembling the pairs of horizontal tracks
] +
1.10d ( 6 ) Assemble anchor tracks 27
( 6a ) Interior garage widths max. BRB + 1030mm (when
installing door in the middle): insert one anchor
track 27 each right and left in track connector 6
and bolt to clip plate 29 and connecting bracket 28
using S6 + S12 making sure they can still be pulled
out
( 6b ) Interior garage widths greater than BRB + 1030mm
( 7 ) Bolt pairs of horizontal tracks 14
16 /16
R
. Make sure:
[ ]
1.25 c

Rebate width 35 - 119mm: Bolt S13 loosely to S12.
Insert S13 through the rectangular hole in moulded
end piece 16
degrees until the square head locks into the punch
hole in angular frame 1

Rebate wider than 120mm: Insert S5 through the
rectangular hole in moulded end piece 16
the top corner and fasten with S12, tightening by hand.
( 8 ) Bolt track connectors 6 with two each S6 + S12 to the VL
corner connecting angles 20
connectors 6 with two each S6 + S12 to the HL sole plate
21 /21
R
Suspending the pairs of horizontal tracks
( 9 ) Fold up pairs of horizontal tracks 14
against falling (safely prop up track connectors 6).
( 10 ) Bolt track arcs 30 using S15 + S12 each to angular frames
1 /1
R L
smooth transition to track profiles, use plumber's
wrench to adjust the ends if necessary).
( 11 ) Bolt moulded end piece 16
[
]
1.30 a
( 12 ) Bolt HL upper deflection pulley bracket 101
the top corner to moulded end piece 16
profile 100 using S11
( 13 ) Use a spirit level to make sure track connectors 6 and pairs
of horizontal tracks 14
wall or ceiling. Do not tighten the screws yet; you may need
to realign.
( 13a ) VL wall fastening: Dowel connecting bracket 28 +
2x each S8 + S9
door!
- 8 -
. Dowel the base of the frame
[ ] [ ]
1.15 a, c, d 2.10 a
[
1.15b
/1 are not twisted or bent during this
R L
or left 14 pair of horizontal tracks with
R L
[
1.20 ca, cb
/20 (S6 + S12)
R L
/21 + fastening profile 100 (S6 + S12)
R L
.
[ ]
1.25 a, b
and HL installation: track connector 6 is ultimately
fastened to the ceiling.
/14
R
to top corner making sure they can still be folded up
L
/16 and in the top corner and turn 90
R L
/1 . Tighten S12 by hand.
R L
/20
R
.
[ ]
2.10 e
L
and connecting plates 18
to top corner using S11.
R/L
.
[ ]
2.15 a
/14 are horizontal, and fasten to
R L
[ ]
1.30 b
[ ] [ ]
1.15 , 2.10
. Caution: Make sure
]
[ ] [ ]
1.20 , 2.10
/16 + S15 and
R L
. Open up
[ ]
1.20 a, b
. Bolt VL corner
]
Bolt HL sole
[ ].
1.20 d
.
[ ]
2.10 c,d,e
[ ] [ ]
1.25 , 2.10
at moulded end piece
L
/16 and in
R L
. Bolt track
[ ]
1.25 d
L
[ ] [ ]
1.30 , 2.15
/14 and safeguard
R L
(ensure
[ ]; [ ]
1.30 a 2.15 a
/101 through
R L
/16 and fastening
R L