User Safety; Technical Features - Jacuzzi J-200 Serie Vorinstallationsblatt

It is the responsibility of the installer/owner to ascer-
tain compliance with specific local regulations prior to
installation.
Jacuzzi Europe S.p.A. gives no guarantee in this re-
spect and refuses all responsibility regarding compli-
ance of the installation carried out.

Technical Features

The Premium spas feature a single-phase power supply (220-240
V). All electro-mechanical parts and pipes are enclosed.
The J-210 is equipped with 1 two-speed pump, whilst the J-
235/245/275 are equipped with 2 pumps.
Maximum absorption of the system
Power supply
(single-phase)
Volt Hertz
50
J-210 220-240 ~
50
J-235 220-240 ~
220-240 ~ 50
J-245
J-275 220-240 ~ 50
The electrical system that powers the spa must absolutely be
sized for maximum consumption (as shown in the table). If suffi-
cient electrical energy is not available, an electronic energy con-
sumption limiter can be activated from inside the electronics box.
This operation can only be performed by authorized Jacuzzi
technicians and limits electricity consumption as follows:
J-210
- alternative consumption: 3.4 kW (when the pump is run at
high speed, the electric heater goes off).
J-235/J-245/J-275
- medium alternative consumption: 5 kW (when 2 pumps are
run at high speed, the electric heater goes off).
- minimum alternative consumption: 3.6 kW (when 1 pump is
run at high speed, the electric heater goes off).
Weights
net weight average fill
kg kg
litres
J-210 ~ 871
~ 227
J-235
~ 347 ~ 1325
~ 1287
J-245 ~ 353
~ 1476
J-275 ~ 402
area involved support area
m 2
J-210 ~ 3,07 ~ 2,48
J-235 ~ 4,54 ~ 3,88
J-245 ~ 3,88
~ 4,54
J-275 ~ 5,22 ~ 4,79
Tot. Consumption: electric
heater + pump(s)
Ampere kW
(k) (j)
21 4,8
(k) (j)
(k): 230 V (k): a 230 V
29 6,7
(single-phase) (monofase)
(j)
(k)
6,7
29
(j): max. power (j): potenza assorbita
(k) (j)
29 6,7 max. absorption
maximum
total max.
water volume
litres
~ 1128 ~ 1355
~ 1703 ~ 2052
~ 1684 ~ 2038
~ 1931 ~ 2334
average load load concentrated
on area involved
on support area
m 2 kg/m 2
~ 441
~ 452
~ 449
~ 447

User safety

I
The system, if installed by qualified personnel, does not present
any hazard for the user. Safety is however also contingent upon
proper use, as set forth by the user's manual included with the
product. The user must contact qualified personnel for special
operations described in the manual.
I
It is important to make sure that personnel tasked to install and
manage the system are qualified as per legal requirements in
effect in the country where installation is carried out.
I
Periodically, however, the differential switch (see "ELECTRICAL
SAFETY" chapter) of the system to which the mini-pool is con-
nected must be checked for efficiency. When you press the
TEST key, the switch must disconnect. If this does not
happen, disconnect the power supply immediately and
contact a qualified technician.
I
For any extra maintenance and/or repairs it is recommended
that you contact an Authorized Service Centre and use only origi-
nal spare parts.
Set up for installation
I
The spa water drain is located behind the front panel, to the
right (or left), dependent on the electric box. The pipe must be
placed in the drain basin when carrying out periodic emptying.
® The Client must ensure a drain basin is provided, suitable sized
and which can be accessed for cleaning operations.
ATTENTION: Before preparing the ground drainage
point, consult the local authority for the regulations
that control the drainage of chemically treated
water.
I
According to the type of installation chosen the ground drainage
point will then be put into position. Premium spas can be installed in
a variety of ways:
- Free standing on the floor or on a specifically prepared base
i
( 4).
- semi-built in by about 4 cm, so that only the spa base is built-
in while the side cover panels remain free (
weight
is appropriate to prepare some removable under-frames (in ma-
kg
rine plywood, etc.) that, besides aesthetically completing installa-
tion, allow the panels to be removed more easily.
I
In any case you will need to provide a support base that is suit-
able for the selected model, taking into consideration the data
contained in the table "Weights".
I
You can use a garden hose to fill the spa.
kg/m 2
~ 546
If the spa is connected, for periodic filling, to the
~ 529
mains system that supplies drinking water, this con-
~ 525
nection must be carried out in compliance with the
~ 487
EN1717 norm, using "AA", "AB" or "AD" anti-pollu-
tion protection procedures. For further information,
14
i
5). In this case, it