Operating Instructions - Jacuzzi j-300 serie Montageanweisung Und Bedienung Und Wartung

heater will come on. The heater goes off when water tempera-
ture has reached 38° C.
N.B.: it is normal for the heater to turn on after the spa is first filled
because tap water is often very cold.
Setting water temperature
Press either the Warmer (
the current temperature setting. The current set temperature
reading will blink once to indicate that the system is ready to ac-
cept changes. Press the Warmer or Cooler button to adjust the
temperature to a desired setting. Once the desired temperature
is reached, do not press any buttons on the control panel for
about 5 seconds. The new temperature setting will blink twice to
indicate that the change has been made.
To access the overtemp feature that allows the spa to reach 41°
C follow the steps below.
A. Press and hold the WARMER (
B. Press and hold the JETS 1 (
2 seconds. You will see the temperature change to 40°C on the
LED display. Press the Warmer (
41°C To lower the temperature, press the Cooler (
C. When the overtemp has been activated, the decimal point
after the last digit will flash on and off every second as an indi-
cator for being in the overtemp mode.
Note: Once the temperature goes below 40°C and you would
like to raise the temperature to 41°C again, you will have to re-
peat the steps above.
Pump activation
The JETS 1 button activates jets pump 1. The first press turns jets
pump 1 on; the second press turns jets pump 1 off. The JETS 2 but-
ton activates jets pump 2 (if equipped). turns jets pump 2 on; the
second press turns jets pump 2 off. When manually activated, either
pump will automatically turn off after 20 minutes.
Light On/Off button
Pressing this button activates the waterfall light, footwell light, light-
ed cup holders, and backlit pillows lights in unison as follows: high
- medium - low - off.
Note: Lights automatically turn off after 2 hours.
Selection of lighting mode
Allows access to 4 light modes for your enjoyment. Press this button to s-
elect your favorite lighting effect as follows:
) or Cooler ( ) button to adjust
) button then;
) button at the same time for
) to raise the temperature to
) button.
Press once
High-Speed Colour Blend Mode:
Display hundreds of colours in 5 second intervals.
Press again
Low-Speed Colour Blend Mode:
Display hundreds of colours in 20 second intervals.
Press again
Freeze Colour Blend Mode:
Selects or "freezes" your low speed blending colour of choice.
Press again
Solid Colour Mode:
Selects one of 7 solid (high-intensity) colours of choice.
Pressing the button again will make the sequence starts from
the beginning.
Another way to use the key:
Jets
The water flow through individual jets in your spa can be ad-
justed or turned off by rotating the outside jet ring. Some jets of-
fer an adjustable center nozzle that allows you to change the
water discharge angle. Simply tilt the center nozzle in these jets
to the desired angle to customize your personal massage. Oth-
er jets offer a spiral action that produces a surging stream of air
and water that provides a vigorous massage.
Note: Always keep at least 6 adjustable jets open at all times to en-
sure proper filtration characteristics within the spa.
Selecting desired massage action
B B C C
A A
Each model incorporates a massage selector that allows you to cus-
tomize the massage and performance by diverting water between
various jet systems. Simply turn massage selector to position A
(Combo), B o C, to divert water pressure to various jet groups.
N.B.: The valve is designed to operate in positions A (Combo), B, and C
for optimum performance.
For optimum filtration benefits, leave the valve in position A when spa
is covered. Select position B or C for maximum jet performance during
spa use.
Adjusting Individual Jet Flow
The water flow to the individual jets in your spa can be increased
or decreased by rotating the outside jet face.
Many jets are also equipped with a direction adjustment module,
so that you can aim the jet in the desired position.
N.B.: always keep at least 6 of these jets open so as to ensure efficient
water filtering.
26