Electrical Safety; Start-Up Instructions - Jacuzzi j-300 serie Montageanweisung Und Bedienung Und Wartung

I
Do not use a spa immediately following strenuous exercise.
I
Be very careful when getting in an out of the spa. All of the sur-
faces are slippery when wet.
I
The spa is not intended for use in public places; always check for
any restrictions and/or regulations concerning the installation and
use of the apparatus in the area chosen.

Electrical safety

®
The MaxiJacuzzi are safe products, manufactured in compliance
with standards
EN 60335-1, EN 60335-2-60, EN 12764
ed during production to ensure user safety.
I
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with
proper installation procedures.
It is the responsibility of the installer to select materials
based on their intended use, to carry out work properly,
to check the condition of the system that the unit will
be connected to and that it ensures safety of use also
concerning maintenance work and the possibility to ex-
amine the system.
I ®
The MaxiJacuzzi are class "I" appliances and therefore they
must be permanently connected, without any intermediate
connections, to the electrical system and to the protection sys-
tem (earth system).
The electrical system of the building must be provided
with a 0.03A differential switch and with an efficient
protection (earth) circuit. Check for proper operation of
the differential switch by pressing the TEST button,
which should trip.
Parts incorporating electrical components, except re-
mote control devices, must be located or fixed so that
they cannot fall into the spa.
Live components and equipment must be out of reach
of individuals in the spa.
I
For connection to the electrical mains, it is necessary to install
an omnipolar cut-off switch as per the values indicated in the
chapter "Electrical characteristics., which is to be located in an
area which is compliant with safety instructions and which can-
not be reached by the users who are using the MaxiJacuzzi
It is mandatory to comply with this instruction. Any other procedure
is prohibited.
I
The installation of electrical devices and equipment (sockets,
switches, etc.) near the MaxiJacuzzi
legal standards and regulations in the country where the
®
MaxiJacuzzi is installed.
I
The disconnection devices must be installed in the power
supply network according to the installation instructions.
and test-
®
.
®
must be in compliance with
I
For the equipotential connection as required by specific
national standards, the installer must use the terminal provided
(standard EN 60335.2.60) in the electrical box, and marked
with the symbol
.
must be established for all metallic masses surrounding the spa,
for example water and gas pipes, metallic platforms, and so on.
Refer to the pre-installation information sheet for instruc-
tions and electrical input of the various models.

Start-up instructions

Read each step in its entirety before proceeding with that
step.
I
Remove any dirt from the spa. Although the spa shell has been
polished at the factory, you may want to treat it with a specially
formulated spa cleaner and wax available from your dealer prior to
filling the first time.
I
Filling the spa
Remove the filter cover, then remove both filter cartridges as
outlined in section "Cleaning The Filters".
Position the end of the hose inside the filter connection and fill
the spa until the level of water covers all of the nozzles, without
however reaching the headrest.
Do not overfill your spa.
N.B.: If your water is extremely hard, it is preferable to fill halfway
with hard water and the rest of the way with softened water.
Always refill the spa through both filter fittings to purge trapped
air from pump intakes. Failure to do so may cause air to be
trapped in either pump 1 or the circulation pump's intake, pre-
venting the pumps from circulating water.
After filling, make sure both filters are installed properly before
applying power to the spa. (refer to sec.) "Cleaning the filters").
I
Checks
Open the cabinet access panel and check all pump fittings to
make sure they are tight. Loosening can occur during shipping
and handling.
I
Turning on power
Turn on power to spa at the home's circuit breaker: the heater and
circulation pump automatically activate. The water temperature LED
flash on the control panel and the messages "COL" or "ICE" appear.
Note: "COL" and "ICE" will only appear when the spa is in Economy
mode.
I
Start-up
Activating the pump(s)
I
Addition of chemical additives at first start-up
Please refer to the Jacuzzi system water treatment guide and relative
catalogue for details on water quality maintenance, the methods
and warnings governing the use of relative chemical products.
23
In particular, an equipotential condition