Operating Instructions - Jacuzzi J-300 series Montageanweisung Und Bedienung Und Wartung

Operating instructions

The spa control system has automatic functions that operate
upon start-up and normal operation to protect the system.
Upon power up, the display shows the following information:
I
current software version;
I
"888" (all LED indicators are on: control of operation of all dis-
play segments and indicator lights).
I
After the initial start-up sequence ends, the actual water tem-
perature is displayed. If water temperature is below 38° C (fac-
tory setting) and the spa is set in skimming/heating mode, the
heater will come on. The heater goes off when water tempera-
ture has reached 38° C.
N.B.: it is normal for the heater to turn on after the spa is first
filled because tap water is often very cold.
Setting water temperature
Press either the Warmer (
just the current temperature setting. The current set tempera-
ture reading will blink once to indicate that the system is ready
to accept changes. Press the Warmer or Cooler button to ad-
just the temperature to a desired setting. Once the desired tem-
perature is reached, do not press any buttons on the control
panel for about 5 seconds. The new temperature setting will
blink twice to indicate that the change has been made.
To access the overtemp feature that allows the spa to reach 41°
C follow the steps below.
A. Press and hold the WARMER (
B. Press and hold the JETS 1 (
for 2 seconds. You will see the temperature change to 40°C on
the LED display. Press the Warmer (
to 41°C To lower the temperature, press the Cooler (
C. When the overtemp has been activated, the decimal point
after the last digit will flash on and off every second as an indi-
cator for being in the overtemp mode.
Note: Once the temperature goes below 40°C and you would
like to raise the temperature to 41°C again, you will have to re-
peat the steps above.
Pump activation
The JETS 1 button activates jets pump 1. The first press turns
jets pump 1 on; the second press turns jets pump 1 off. The
JETS 2 button activates jets pump 2 (if equipped). turns jets
pump 2 on; the second press turns jets pump 2 off. When man-
ually activated, either pump will automatically turn off after 20
minutes.
) or Cooler ( ) button to ad-
) button then;
) button at the same time
) to raise the temperature
) button.
Light On/Off button
Pressing this button activates the waterfall light, footwell light,
lighted cup holders, and backlit pillows lights in unison as fol-
lows: high - medium - low - off.
Note: Lights automatically turn off after 2 hours.
Selection of lighting mode
Allows access to 4 light modes for your enjoyment. Press this but-
ton to select your favorite lighting effect as follows:
Press once
High-Speed Colour Blend Mode:
Display hundreds of colours in 5 second intervals.
Press again
Low-Speed Colour Blend Mode:
Display hundreds of colours in 20 second intervals.
Press again
Freeze Colour Blend Mode:
Selects or "freezes" your low speed blending colour of choice.
Press again
Solid Colour Mode:
Selects one of 7 solid (high-intensity) colours of choice.
Pressing the button again will make the sequence starts
from the beginning.
Another way to use the key:
Jets
The water flow through individual jets in your spa can be adjusted
or turned off by rotating the outside jet ring. Some jets offer an
adjustable center nozzle that allows you to change the water dis-
charge angle. Simply tilt the center nozzle in these jets to the de-
sired angle to customize your personal massage. Other jets of-
fer a spiral action that produces a surging stream of air and wa-
ter that provides a vigorous massage.
Note: Always keep at least 6 adjustable jets open at all times
to ensure proper filtration characteristics within the spa.
Selecting desired massage action
B B C C
A A
Each model incorporates a massage selector that allows you
to customize the massage and performance by diverting wa-
ter between various jet systems.
Simply turn massage selector to position A (Combo), B o C, to
divert water pressure to various jet groups.
26