Changing Parameter Settings; Resetting A Parameter To The Factory-Set Value - Yamaha RX-V1300RDS Bedienungsanleitung

SOUND FIELD PROGRAM PARAMETER EDITING

Changing Parameter Settings

You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
Adjustments should be made with the remote control.
y
• We recommended that you edit the parameter while using a
video monitor. It is easier to see the video monitor than it is to
see the front panel display.
TRANSMIT RE–NAME
SYSTEM
POWER STANDBY
A PHONO
V-AUX CBL/SAT MD/TAPE
D-TV/LD VCR 1 VCR2/DVR
POWER
1
TV
REC
1
Press AMP to select the
AMP mode.
AMP appears in the display
window on the remote control.
2
Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3
Select a DSP program you want to adjust.
HALL
ENTER-
TAINMENT
MOVIE
THEATER 2
Program No.
P04 ROCK CONCERT
Cursor
≥ D S P L E V E L ... ... ... ... 0 d B
I N I T . D L Y ... ... ... ... 1 5 m s
R O O M S I Z E ... ... ... ... 1 . 0
L I V E N E S S ... ... ... ... ... ... ... 5
R E V . T I M E ... ... ... ... 1 . 6 s
R E V . D E L A Y ... ... 1 2 0 m s
Parameters
Example of the parameter setting display
70
0110V1300_69-74_EN-GB.p65
CLEAR LEARN
SLEEP 6CH INPUT
TUNER CD
REC
AUDIO
+
DISC SKIP
CD-R
VOL
DVD
–
LEVEL SET MENU MUTE
+
TITLE MENU
TV VOL
4
SELECT TV INPUT A/B/C/D/E
CH CH
TV MUTE
– +
POWER
AMP SELECT
2
AV
PRESET PRESET
TEST ON SCREEN STEREO
TV VOL
5 –
RETURN DISPLAY
EFFECT
ROCK
HALL CHURCH JAZZ CLUB CONCERT
1 2 3 4 3
ENTER- MUSIC TV MOVIE
TAINMENT VIDEO THEATER THEATER 1
5 6 7 8
MOVIE /DTS
EX/ES
THEATER 2 SUR. SELECT
9 10 11 12
+
0 10 CHP/INDEX
AMP
ON SCREEN
DISPLAY
ROCK
CHURCH JAZZ CLUB CONCERT
1 2 3 4
MUSIC TV MOVIE
VIDEO THEATER THEATER 1
5 6 7 8
/DTS
SUR. SELECT EX/ES
9 10 11 12
+
0 10 CHP/INDEX
Program name
Parameter valves
70
4
Press u / d to select the
parameter.
5
Press j / i to change the
parameter value.
y
• When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6
Repeat steps 3 to 5 above as necessary to
change other program parameters.
Notes
• The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press u / d.
• You cannot change parameter values when "14 MEMORY
GUARD" on the SET MENU is set to ON. If you want to
change the parameter values, set "14 MEMORY GUARD" to
OFF (see page 66).
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
I To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold j / i until the value temporarily stops at the factory-
set value. The asterisk mark (*) by the parameter name
disappears on the video monitor.
I To reset all of the parameters to
the factory-set values
Use "9 PARAM. INI" on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 64).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
2002.11.07, 12:09
+
TV VOL
CH CH
TV MUTE
+
–
SELECT
PRESET PRESET
TV VOL
–
+
TV VOL
CH CH
TV MUTE
+
–
SELECT
PRESET PRESET
TV VOL
–