Herunterladen Inhalt Inhalt Diese Seite drucken

Getting Started With The Generating Set - SDMO DIESEL 6000 E SILENCE AVR Benutzer- Und Wartungshandbuch/Übersetzung Der Original-Anleitung

Vorschau ausblenden Andere Handbücher für DIESEL 6000 E SILENCE AVR:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 41
2.7.4 Connection and choice of cables
For all connections, use flexible, strong rubber-sheathed cables which comply with standard IEC 60245-4 or equivalent cables, and
ensure that these are kept in perfect condition. Only use one class I electrical device per socket and connect up equipment using a
cable equipped with a PE protective conductor (green/yellow); this protective conductor is not required for class II equipment.
Adhere to the cross sections and lengths recommended in this table during installation or when using electrical extensions.
Generating set type:
Generating set socket type:
Recommended cable cross section:
Length of
cable used
101 to 150 m*
*This cable length is the maximum permitted length, and must not be exceeded.
Installation method = cables on raceway or non-drilled tablet/Permitted drop in voltage = 5%/Multi-core conductors/Cable type PVC
70°C (e.g. H07RNF)/Ambient temperature =30°C.
2.8
Risks during handling operations, use and maintenance
For safety reasons, all operations must be carried out by staff with the necessary skills and using suitable equipment. Maintenance
must be carried out regularly and properly using only original or equivalent parts. Gloves must be worn.
Safety guidelines for handling petroleum products:
DANGER
Safety guidelines for handling batteries:
DANGER

3 Getting started with the generating set

3.1
Key to illustrations
The cover illustrations can be used to identify the various components of the generating set. The procedures in the manual refer to
these illustrations using letters and numbers as identifiers: "A1" refers to the number 1 on figure A.
Earth terminal
Starter battery
Key
Fuel tap
Retention container
Oil level dipstick
Oil filler cap
Fuel level indicator
Fuel tank cap
APM202
Electrical connectors
Working hours counter
Stop lever
* Source transfer switch, battery charger, etc.
10 A
mm²
0 to 50 m
4
51 to 100 m
10
10
RISK OF EXPLOSION
Respect the local regulations in force concerning the handling of petroleum products.
Filling should be carried out with the engine switched off and cold. Smoking, using a
naked flame or producing sparks are forbidden while the fuel tank is being filled. After
filling, always check that the tank's filler cap is properly tightened. Clean any traces of
fuel with a clean cloth and wait until the vapours have dispersed before starting the
generating set.
The fluids used by generating sets, such as oils and fuels, are dangerous products.
Never ingest them. Avoid prolonged or repeated contact with the skin.
RISK OF POISONING OR EXPLOSION
Follow the battery manufacturer's recommendations. Use insulated tools
only. Never use sulphuric acid or acid water to top up the electrolyte level.
Never leave the battery close to a flame or fire. Always ensure adequate
ventilation during charging.
A1
Oil drain tap
A2
Oil filter
A3
Fuel filters
A4
Generating set top cover
A5
Access door to the generating set
A6-B1
Fuse holder
A7
Panel lighting
A8
Circuit breakers
A9
Connection for options*
A10
Lifting eye
A11
Oil drain pipe
A12
Air filter
A13
Solenoid valve
Single phase
16 A
AWG
mm²
AWG
mm²
10
6
9
7
10
7
7
16
5
A14-B5
A15
A16-C1
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
Three-phase
32 A
10 A
AWG
mm²
AWG
10
7
1.5
14
25
3
2.5
12
35
2
4
10
Exhaust silencer
Dipstick upper limit
Dipstick lower limit
Oil filter screw
Hose clips
Retaining clip
Retaining clip screw
Wheel
Air filter cover
Wing nut
Foam element
Paper element
Rubber seal
16 A
mm²
AWG
2.5
12
4
10
6
9
A27
B2
B3
B4
C2
C3
C4
D1
D2
D3
D4
D5
D6

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis