Functional Description - Makita CB100D Betriebsanleitung

FUNCTIONAL
DESCRIPTION
Power button
To turn on the blanket, press and hold the power button
for a few seconds. To turn off, press and hold the power
button again.
Temperature adjustment
CAUTION:
For continuous operation, set the
temperature setting to "low" (blue). If the heating
section touches the same part of the skin for a long
time, there is a possibility of low temperature burns.
There are three temperature settings (high, medium,
low). When you switch on the blanket, the temperature
is set to "high". Each time you press the power button,
WKH WHPSHUDWXUH VHWWLQJ FKDQJHV DV VKRZQ LQ WKH ¿JXUH
The color of the power button shows the current setting.
Fig.10: 1. Red: "high" 2. White: "medium" 3. Blue:
"low"
,QGLFDWLQJ WKH UHPDLQLQJ EDWWHU\
FDSDFLW\
Only for battery cartridges with the indicator
Fig.11: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
Indicator lamps
Lighted Off
(For 14.4 V and 18 V batteries only)
(For 14.4 V and 18 V batteries only)
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Remaining
FDSDFLW\
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
11 ENGLISH
%DWWHU\ SURWHFWLRQ V\VWHP
The device is equipped with a battery protection sys-
tem. This system automatically cuts off power to the
heating parts to extend battery life. If the remaining
battery capacity is too low, the device will not operate.
When you turn the device on, the power is supplied to
the heating parts again, but stops soon. In this situation,
remove and recharge the battery cartridge.
Connecting USB devices
CAUTION:
&RQQHFW RQO\ GHYLFHV WKDW DUH
FRPSDWLEOH ZLWK WKH 86% SRZHU VXSSO\ SRUW Not
doing so may cause a malfunction of the battery
holder.
NOTICE:
Before connecting a USB device to
WKH EDWWHU\ KROGHU ZLWK WKH EDWWHU\  DOZD\V EDFN
up the data on the USB device. Not doing so may
cause a loss of your data.
The battery holder (with the battery cartridge) can work
as an external power supply for USB devices.
Open the cover and connect a USB cable (not included)
to the power supply port of the battery holder. Then con-
nect the other end of the cable to the device and turn on
the switch next to the USB port.
The battery holder (with the battery cartridge) supplies
DC 5 V, 2.4 A (maximum).
Fig.12: 1. Cover 2. Switch
NOTE: The battery holder may not supply power to
some USB devices.
NOTE: When not in use or after charging, remove the
USB cable and close the cover.
NOTE: Battery power is consumed while the switch is
turned on. Always turn off the switch when not in use.
NOTE: When charging multiple USB devices in suc-
cession, wait about 10 seconds after charging of the
previous device has completed before beginning to
charge the next device.
Usage examples
By fastening the snap buttons and strap on the blanket,
you can use the blanket for warming up your shoulders
and waist.
Fig.13
Fig.14: 1. Snap button 2. Strap
Fig.15: 1. Snap button 2. Strap
NOTICE:
To prevent the damage to the heating
element inside the blanket, do not use the blanket
as a cushion or a rug.
NOTICE:
:KHQ \RX ZHDU WKH EODQNHW RQ \RXU
shoulders or waist, be sure to fasten the snap
button or tighten the strap.