ims PRO IMS SPOT ARCPULL 200 Bedienungsanleitung Seite 23

Placing a dowel pin holder (059634 - 059641)
• Insert the dowel pin holder in its support.
• Put the protection nozzle on the dowel pin support and tighten slightly
• Reposition the electrode holder in the canon of the gun
• Put the protection pad at the end of the earth rods
• Tighten the two holding screws for the pad and make sure there is a
slight contact with the earth rods to guarantee electrical contact.
ERROR MESSAGE, ANOMALIES, CAUSES, SOLUTIONS
ing 1.5mm
e Gas
t I
ms A
This equipment has a failure control system. In case of failure, error messages may be displayed.
100 200
+1 2.0
Error code
zone de message
message
message area area
Ring 1.5mm
Fe Gas
+1 2.0
ERVOLTAGE DEFECT OVERHEATING DEFECT
ing 1.5mm
message zone de
e Gas
message
t area I
ms A
100 200
+1 2.0
zone de message
message
message area area
PRESSED KEY
COM. DEFECT
OVERVOLTAGE DEFECT
Ring 1.5mm
Fe Ring 1.5mm Gas
Info
Ring 1.5mm
Fe Gas
Fe Gas
Soft gene V0.0
+1 2.0
Hard gene V0.0
+1 2.0
ERVOLTAGE DEFECT OVERHEATING DEFECT
+1 2.0
message zone de
Soft gun V0.0
message
message zone de area
ERHEATING DEFECT Hard gun V0.0
message message zone de area
COM. DEFECT
message area
PRESSED KEY
COM. DEFECT
OVERVOLTAGE DEFECT
OVERVOLTAGE DEFECT
MOTOR DEFECT
OVERVOLTAGE DEFECT Info
OVERHEATING DEFECT
Soft gene V0.0
Hard gene V0.0
Soft gun V0.0
ERHEATING DEFECT Hard gun V0.0
COM. DEFECT
COM. DEFECT
COM. DEFECT
MOTOR DEFECT
MOTOR DEFECT
OVERHEATING DEFECT
OVERHEATING DEFECT
OVERHEATING DEFECT
MOTOR DEFECT
MOTOR DEFECT
MOTOR DEFECT
All operations requiring the removal of the machine's cover and checking the electrical systems must be done by a
qualified technician.
IMS SPOT ARCPULL 200
Main Menu
> Settings
Manual Mode
Configuration
Meaning
Main Menu
Configuration
> Pregas > 100ms
Generator thermal Maximum duty cycle
> Settings
Postgas 500ms
Manual Mode
Language EN
Configuration
protection reached.
Product reset
t I
Main Menu
Info
ms A
100 200
> Settings
Manual Mode
message
Configuration
Configuration
Manual Settings
area
> Pregas
Mains voltage Mains power is out of
Postgas
Language
default. range or one phase is
Product reset
Configuration Main Menu
Info
Start-up > Q = 0
Main Menu
missing.
Main Menu
> Pregas > 100ms
Postgas 500ms > Settings
OVERHEATING DEFECT
Language EN Manual Mode
> Settings
Product reset > Settings Manual Mode Configuration Manual Settings
Synergic Settings
t I
Info Configuration Manual Mode
ms A
t I
Configuration
> Material > Fe
ms A
100 t I 200
Gas ms A ON
100 200
Electrode Ring
100 200
message
THK. elec. 1.5 mm
Configuration
Manual Settings
Start-up
area
Keypad fault message A key on the keypad is
Configuration
PRESSED KEY
message area
> Pregas Configuration
area
> Pregas Postgas
pushed when the machine
> Pregas Language
Postgas
Language Postgas Product reset Synergic Settings
Product reset
Info is switched on.
Info Product reset Language
Start-up > Q = 0
Product reset
> Material Info
Soft gene V0.0
Info Gas
Hard gene V0.0
Electrode
OVERHEATING DEFECT
THK. elec.
OVERHEATING DEFECT
Soft gun V0.0
Synergic Settings Manual Settings
OVERHEATING DEFECT Communication :3 sec Communication between
Hard gun V0.0
Manual Settings
to reset
Manual Settings
> Material > Fe
fault with the gun the gun and the generator
Gas ON
Electrode Ring
Product reset
THK. elec. 1.5 mm
is not working
Start-up
Start-up
PRESSED KEY
Start-up
PRESSED KEY
PRESSED KEY
Synergic Settings
Product reset
:3 sec
Info
Gun thermal pro- Maximum duty cycle
Synergic Settings
to reset
Info
> Material Synergic Settings
Soft gene Info V0.0
tection reached.
> Material Gas
Soft gene Hard gene V0.0 V0.0
> Material Electrode Gas
Soft gene Hard gene V0.0 V0.0
THK. elec. Gas
Electrode
Soft gun Hard gene V0.0 V0.0
:3 sec THK. elec. Electrode
Hard gun Soft gun V0.0 V0.0
THK. elec.
to reset
Soft gun V0.0
Hard gun V0.0
Hard gun V0.0
Product reset
Gun motor fault Gun mechanism is blocked Reconnect the gun and switch the machine
Product reset
Product reset
:3 sec
to reset
:3 sec
to reset :3 sec
to reset
Causes
> 100ms
500ms
EN
> Q = 0
> 100ms
> 100ms 500ms
> 100ms EN
500ms
EN 500ms
EN
> Fe
ON
Ring
1.5 mm
> Q = 0
> Q = 0
> Q = 0
> Fe
> Fe ON
> Fe ON Ring
1.5 mm ON
Ring
Ring 1.5 mm
1.5 mm
Dowel pin holder
Protective nozzle
Pad
Solutions
Wait for the indicator to turn off before resu-
ming welding operations.
Have your electrical installation checked by
a qualified person. The voltage between
phase and neutral must be between 100V
and 127Vac on a 110V supply network or
between 200V and 265Vac on a 230Vac
supply network.
Ask a qualified person to check the keypad.
Reconnect the gun and switch the machine
back on. If the fault remains, ask a qualified
person to check the product.
Wait for the indicator to turn off before resu-
ming welding operations.
back on. If the fault remains, ask a qualified
person to check the product.
EN
Dowel pin holder support
Pad
holding
screw
23