Vitek VT-3600 BW Betriebsanweisung Seite 5

• To avoid obstructions do not apply excessive force
while pushing meat with the pusher (1).
• If any hard piece of food stops the feeder screw
or cutting blade rotation, switch the unit off im-
mediately and use the screw reverse mode «REV»
(reverse) to remove the obstruction before start-
ing again.
BEFORE USING THE MEAT GRINDER
After unit transportation or storage at low tempera-
ture it is necessary to keep it for at least two hours
at room temperature before switching on.
• Unpack the meat grinder and remove all package
materials, clean the unit body with a damp cloth and
then wipe it dry.
• Wash all removable parts with warm water and neu-
tral detergent, then rinse and dry thoroughly before
assembling.
• Before using the unit for the first time, make sure
that voltage in your mains corresponds to the oper-
ating voltage of the unit.
USING THE MEAT GRINDER
• The meat grinder is intended only for household
processing products and making homemade semi-
finished products.
• Assemble the unit and place it on a flat dry surface.
• Make sure that ventilation openings on the body are
not blocked.
• Insert the power plug into the mains socket, the but-
ton (11) « » illumination will light up.
• Place a suitable bowl under the meat grinder head
(3).
• Make sure that the meat is fully defrosted, re-
move excess fat and all bones, and cut the meat
into cubes or strips fitting the opening of the food
tray (2).
• Switch the unit on by pressing the button (11) «
• Slowly feed the meat pieces into the grinder head
body (3) using the pusher (1).
• During operation use only the pusher (1) supplied
with the unit.
• Do not use any other objects to push products; do
not push the meat with your hands.
• Do not apply excessive effort while pushing the
meat or other food.
• Obstructions can appear during grinding meat or
other products, use the screw reverse mode «REV»
to remove the obstruction. To switch the screw re-
verse mode «REV» on, switch the meat grinder off
by pressing the button (11) «
button (10) « », the illumination of this button will
light up, and then switch the unit on by pressing the
button (11) « ».
• Do not run the unit for more than 5 minutes con-
tinuously.
• After 5 minutes of continuous use, switch the meat
• After you finish operating, switch the meat grinder
MEAT GRINDING
1. Install the meat grinder head (3) to the attaching
2. Install the screw (12) into the meat grinder head (3)
3. Install the crossed blade (13) (pic. 4).
4. Select one of the grates (14 or 15) and set it above
Attention!
– Face the blade cutting side to the grate. If the
– Coarse grate (14) is intended for processing
– Fine grate (15) is intended for processing both
5. Place the food tray (2) on the meat grinder head
6. Insert the power plug into the mains socket, the but-
7. Switch the meat grinder on by pressing the button
8. During the operation use only the pusher (1).
Note:
–
».
–
9. After you finish operating, switch the meat grinder
10. To remove the meat grinder head press the lock
11. To disassemble the meat grinder head, unscrew
», then press the
AUTO SWITCH-OFF FUNCTION
The meat grinder is equipped with auto switch-off func-
tion in case of motor unit overheating.
• In case of overheating of the motor, the automatic
• In this case immediately remove the power plug
5
grinder off and let it cool down during 10-15 minutes
before further operation.
off, pressing the button (11) «
and only after that you can disassemble it.
point (4), and turn it counterclockwise until bump-
ing (pic. 1, 2).
body (pic. 3).
the blade, matching the ledges on the grate with the
grooves on the meat grinder head body (3), tighten
the nut (16) (pic. 5, 6).
blade is installed improperly, it will not grind
the products.
raw meat, vegetables, dried fruit, cheese, fish,
etc.
raw and cooked meat, fish, etc.
body (3).
ton (11) « » illumination will light up.
(11) « ».
For better meat processing slice it in cubes or
stripes. Defrost frozen meat thoroughly.
During the operation use only the pusher supplied
with the unit; do not use any other objects to push
the meat; never push the meat with your fingers.
off, pressing the button (11) «
unit; after that you can disassemble it.
button (5), turn the meat grinder head (3) clockwise
and remove it.
the nut (16) and take out the installed grate (14 or
15), the blade (13) and the screw (12) from the meat
grinder head body.
thermal switch will be on, and the meat grinder will
be switched off.
from the mains socket.
ENGLISH
», unplug the unit,
», and unplug the